PIC18F4439-E/PT Microchip Technology, PIC18F4439-E/PT Datasheet - Page 16
![IC PIC MCU FLASH 6KX16 44TQFP](/photos/6/82/68251/c04-076_pt_sml.jpg)
PIC18F4439-E/PT
Manufacturer Part Number
PIC18F4439-E/PT
Description
IC PIC MCU FLASH 6KX16 44TQFP
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC18F2439-ISO.pdf
(322 pages)
3.PIC18F2439-ISO.pdf
(6 pages)
4.PIC18F2439-ISO.pdf
(34 pages)
Specifications of PIC18F4439-E/PT
Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
12KB (6K x 16)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
640 x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
44-TQFP, 44-VQFP
Processor Series
PIC18F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
640 B
Interface Type
I2C, SPI, AUSART
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
32
Number Of Timers
16 bit
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
DV164005, DV164136
Minimum Operating Temperature
- 40 C
On-chip Adc
8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F4439-E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC18FXX39
3.4
Data EEPROM is accessed one byte at a time via an
Address Pointer, EEADR, and a data latch, EEDATA.
Data EEPROM is written by loading EEADR with the
desired memory location, EEDATA with the data to be
written, and initiating a memory write by appropriately
configuring the EECON1 and EECON2 registers. A
byte write automatically erases the location and writes
the new data (erase-before-write).
When using the EECON1 register to perform a data
EEPROM write, the EEPGD bit must be cleared
(EECON1<7> = 0) and the CFGS bit must be cleared
(EECON1<6> = 0). The WREN bit must be set
(EECON1<2> = 1) to enable writes of any sort, and this
must be done prior to initiating a write sequence. The
write sequence is initiated by the setting the WR bit
(EECON1<1> = 1). It is strongly recommended that the
WREN bit be set only when absolutely necessary.
To help prevent inadvertent writes when using the
EECON1 register, EECON2 is used to “enable” the WR
bit. This register must be sequentially loaded with 55h
and then, AAh, immediately prior to asserting the WR
bit in order for the write to occur.
The write will begin on the falling edge of the 4th SCLK
after the WR bit is set.
After the programming sequence terminates, SCLK
must still be held low for the time specified by
parameter P10 to allow high voltage discharge of the
memory array.
FIGURE 3-9:
DS30480C-page 16
SCLK
SDATA
Data EEPROM Programming
4-bit Command
1
0
2
0
3
0
4
0
P5
DATA EEPROM WRITE TIMING
BSF EECON1, WR
1
2
15 16
P5A
4-bit Command
1
0
2
0
3
0
Preliminary
SDATA = Input
4
0
P5
1
0
Data Payload
2
0
16-bit
FIGURE 3-8:
15 16
0
0
P5A
4-bit Command
1
0
2
No
0
3
0
Unlock Sequence
for Write to Occur
AAh - EECON2
Delay P11+P10
55h - EECON2
4
0
PROGRAM DATA FLOW
Enable Write
Set Address
Start Write
Sequence
2010 Microchip Technology Inc.
Set Data
Done?
Start
Done
Data EEPROM
Yes
Write Time
P11
P10
Data Payload
16-bit
1
n
2
n