LMV358IDT STMicroelectronics, LMV358IDT Datasheet - Page 2

• Manufacturer Part Number: LMV358IDT
• Description: IC OP AMP DUAL R-R LP I/O 8-SOIC
• Manufacturer: STMicroelectronics

Specifications of LMV358IDT

• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Output Type: Rail-to-Rail
• Slew Rate: 0.45 V/µs
• Gain Bandwidth Product: 1.3MHz
• Current - Input Bias: 16nA
• Voltage - Input Offset: 100µV
• Current - Supply: 162µA
• Current - Output / Channel: 48mA
• Voltage - Supply, Single/dual (±): 2.7 V ~ 6 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Number Of Channels: 2
• Common Mode Rejection Ratio (min): 65 dB
• Input Offset Voltage: 3 mV
• Input Bias Current (max): 85 nA
• Operating Supply Voltage: 3 V, 5 V
• Supply Current: 0.44 mA
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Shutdown: No
• Supply Voltage (max): 6 V
• Supply Voltage (min): 2.7 V
• Voltage Gain Db: 97 dB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-4945-2

Absolute maximum ratings and operating conditions
1
2/16
Absolute maximum ratings and operating conditions
Table 1.
1. All voltage values, except differential voltage are with respect to network terminal.
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. If
3. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-
4. Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a
5. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between
6. Charged device model: all pins and the package are charged together to the specified voltage and then
7. Short-circuits from the output to V
Symbol
V
resistor must be added to limit input current.
circuits on all amplifiers. All values are typical.
1.5 k Ω resistor between two pins of the device. This is done for all couples of connected pin combinations
while the other pins are floating.
two pins of the device with no external series resistor (internal resistor < 5 Ω ). This is done for all couples of
connected pin combinations while the other pins are floating.
discharged directly to the ground through only one pin. This is done for all pins.
No value specified for CDM on SOT23-5L package. The value is given for SO and TSSOP packages.
approximately 48 mA, independent of the magnitude of V
simultaneous short-circuits on all amplifiers.
T
R
R
ESD
V
T
V
V
id
oper
T
thja
CC
stg
thjc
id
in
j
> ±1 V, the maximum input current must not exceed ±1 mA. In this case (V
Supply voltage
Differential input voltage
Input voltage
Operating free air temperature range
Storage temperature
Maximum junction temperature
Thermal resistance junction to ambient
Thermal resistance junction to case
HBM: human body model
MM: machine model
CDM: charged device model
Lead temperature (soldering, 10sec)
Output short-circuit duration
Absolute maximum ratings
SOT23-5
SO-8
SO-14
TSSOP8
TSSOP14
SOT23-5
SO-8
SO-14
TSSOP8
TSSOP14
(1)
Parameter
CC
(5)
Doc ID 11887 Rev 4
can cause excessive heating. The maximum output current is
(2)
(4)
(6)
(3)
(3)
CC
. Destructive dissipation can result from
V
DD
LMV321, LMV358, LMV324
-40 to + 125
-0.3 to V
-65 to +150
see note
id
Value
> ±1 V), an input series
150
250
125
103
120
100
200
250
1.5
±1
81
40
31
37
32
7
2
CC
(7)
+0.3
°C/W
°C/W
Unit
°C
°C
°C
kV
kV
°C
V
V
V
V