LM2902AWYDT STMicroelectronics, LM2902AWYDT Datasheet - Page 2

• Manufacturer Part Number: LM2902AWYDT
• Description: IC OP AMP QUAD 1.3MHZ 14SOIC
• Manufacturer: STMicroelectronics

Specifications of LM2902AWYDT

• Amplifier Type: General Purpose
• Number Of Circuits: 4
• Slew Rate: 0.4 V/µs
• Gain Bandwidth Product: 1.3MHz
• Current - Input Bias: 20nA
• Current - Supply: 1.5mA
• Current - Output / Channel: 20mA
• Voltage - Supply, Single/dual (±): 3 V ~ 30 V, ±1.5 V ~ 15 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• -3db Bandwidth: -
• Voltage - Input Offset: -
• Other names: 497-10426-2

Absolute maximum ratings and operating conditions
1
2/18
Absolute maximum ratings and operating conditions
Table 1.
1. Short-circuits from the output to V
2. This input current only exists when the voltage at any of the input leads is driven negative. It is due to the
3. R
4. Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a
5. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between
6. Charged device model: all pins and the package are charged together to the specified voltage and then
Table 2.
Symbol
Symbol
maximum output current is approximately 20 mA, independent of the magnitude of V
collector-base junction of the input PNP transistor becoming forward biased and thereby acting as input
diode clamps. In addition to this diode action, there is also NPN parasitic action on the IC chip. This
transistor action can cause the output voltages of the op-amps to go to the V
for a large overdrive) for the time during which an input is driven negative. This is not destructive and
normal output is restored for input voltages higher than -0.3 V.
1.5kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations
while the other pins are floating.
two pins of the device with no external series resistor (internal resistor < 5Ω). This is done for all couples of
connected pin combinations while the other pins are floating.
discharged directly to the ground through only one pin. This is done for all pins.
T
R
ESD
R
V
V
V
T
V
thja/c
oper
V
I
CC
thja
thjc
CC
icm
stg
in
id
i
are typical values.
Supply voltage
Differential input voltage
Input voltage
Output short-circuit to ground
Input current
Storage temperature range
Thermal resistance junction to ambient
Thermal resistance junction to case
HBM: human body model
MM: machine model
CDM: charged device model
Supply voltage
Common mode input voltage range
Operating free-air temperature range
Absolute maximum ratings
Operating conditions
SO-14
TSSOP14
DIP14
SO-14
TSSOP14
DIP14
T
min
≤ T
amb
(2)
≤ T
max
Parameter
Parameter
(5)
CC
+
can cause excessive heating and potential destruction. The
(4)
(6)
(1)
(3)
(3)
V
-0.3 to V
V
CC
CC
-65 to +150
-40 to +125
-
±16 to 32
to V
-
3 to 30
Infinite
Value
Value
CC
1500
to V
+32
105
100
800
100
50
80
31
32
33
CC
voltage level (or to ground
CC
CC
+
+
+ 0.3
+
CC
- 1.5
- 2
+
LM2902W
°C/W
°C/W
Unit
Unit
mA
°C
°C
V
V
V
V
V
V
V
V