NCP565D2TG ON Semiconductor, NCP565D2TG Datasheet - Page 17

• Manufacturer Part Number: NCP565D2TG
• Description: IC REG LDO 1.5A ADJ VOLT D2PAK-5
• Manufacturer: ON Semiconductor

Specifications of NCP565D2TG

• Regulator Topology: Positive Adjustable
• Voltage - Output: 0.9 ~ 7.7 V
• Voltage - Input: 2.5 ~ 9 V
• Voltage - Dropout (typical): 0.9V @ 1.5A
• Number Of Regulators: 1
• Current - Output: 1.5A
• Current - Limit (min): 1.6A
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: TO-263-5, D²Pak (5 leads + Tab), TO-263BA
• Number Of Outputs: 1
• Polarity: Positive
• Input Voltage Max: 9 V
• Output Voltage: 0.9 V to 7.7 V
• Output Type: Adjustable
• Dropout Voltage (max): 1.3 V at 1500 mA
• Output Current: 1.5 A
• Line Regulation: 0.03 %
• Load Regulation: 0.03 %
• Voltage Regulation Accuracy: 3 %
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Reference Voltage: 0.927 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: NCP565D2TG; NCP565D2TGOS

PUBLICATION ORDERING INFORMATION
The product described herein (NCP565), may be covered by one or more of the following U.S. patents: 5,920,184; 5,834,926.
There may be other patents pending.
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [e-mail]
ON Semiconductor and
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
2X
REFERENCE
6X
2X
0.15
0.10
0.08
6X
6X
PIN 1
0.15
L1
L
C
C
C
Ç Ç Ç Ç
Ç Ç Ç Ç
Ç Ç Ç Ç
C
1
6
BOTTOM VIEW
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
TOP VIEW
SIDE VIEW
D2
D
3
4
(A3)
4X
e
6X
A
A1
b
K
B
E
0.10
0.05
E2
(NOTE 3)
A
N. American Technical Support: 800−282−9855 Toll Free
Europe, Middle East and Africa Technical Support:
Japan Customer Focus Center
C A B
C
PACKAGE DIMENSIONS
USA/Canada
Phone: [phone]
Phone: 81−3−5773−3850
DFN6, 3x3.3, 0.95 PITCH
C
http://onsemi.com
SEATING
PLANE
CASE 506AX−01
ISSUE O
17
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
2.15
0.83
6X
SOLDERING FOOTPRINT*
1
NOTES:
1. DIMENSIONS AND TOLERANCING PER ASME
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
4. COPLANARITY APPLIES TO THE EXPOSED PAD
Y14.5M, 1994.
AND IS MEASURED BETWEEN 0.25 AND 0.30 mm
FROM TERMINAL.
AS WELL AS THE TERMINALS.
DIM
A1
A3
D2
E2
L1
A
D
E
K
b
e
L
MIN
0.80
0.00
0.30
1.90
1.10
0.20
0.40
0.00
3.60
1.35
MILLIMETERS
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
3.00 BSC
3.30 BSC
0.95 BSC
0.20 REF
NOM
−−−
−−−
−−−
−−−
−−−
−−−
−−−
−−−
DIMENSIONS: MILLIMETERS
MAX
0.90
0.05
0.40
2.10
1.30
0.60
0.15
−−−
0.50
6X
PITCH
0.95
NCP565/D