P0080SCMC Littelfuse / Teccor Sidactor(R) Product, P0080SCMC Datasheet - Page 132
![no-image](/images/manufacturer_photos/0/3/393/littelfuse___teccor_sidactor_r__product_sml.jpg)
P0080SCMC
Manufacturer Part Number
P0080SCMC
Description
SIDACTOR MC BI 6V 400A DO-214AA
Manufacturer
Littelfuse / Teccor Sidactor(R) Product
Series
SIDACtor® SC(MC)r
Datasheet
1.P0080SCMC.pdf
(212 pages)
Specifications of P0080SCMC
Voltage - Breakover
25V
Voltage - Off State
6V
Voltage - On State
5V
Current - Peak Pulse (8 X 20µs)
400A
Current - Peak Pulse (10 X 1000µs)
100A
Current - Hold (ih)
50mA
Number Of Elements
1
Capacitance
75pF
Package / Case
DO-214AA, SMB
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P0080SCMC
Manufacturer:
Littelfuse
Quantity:
45 000
Company:
Part Number:
P0080SCMCL
Manufacturer:
Littelfu
Quantity:
150 000
Company:
Part Number:
P0080SCMCLRP
Manufacturer:
Littelfu
Quantity:
73 500
Part Number:
P0080SCMCLRP
Manufacturer:
LITTELFUSE/力特
Quantity:
20 000
Company:
Part Number:
P0080SCMCRP
Manufacturer:
Littelfu
Quantity:
30 000
GR 1089–Core
Table 4.7 Second Level AC Power Fault Test for Non-Customer Premises Equipment
Notes:
1. Primary protectors are removed for all tests.
2. For EUT containing secondary voltage limiting and current limiting protectors, tests are to be performed at the indicated voltage(s)
3. This test is to be performed between the ranges of 100 V to 600 V and is intended to produce the greatest heating affect.
4. Test 5 simulates a high impedance induction fault. Specific information regarding this test is available upon request.
5. These tests are repeated using a short-circuit value just below the operating threshold of the current limiting device, or, if the EUT
6. Intra-building, second level lower fault test uses test condition 1 only. The applied voltage is at 120 V rms only.
Table 4.8 Second Level AC Power Fault for Customer Premises Equipment
Notes:
1. Applied between exposed surfaces and Ground
2. The 60 Hz signal is applied with an initial amplitude of 30 V rms and increased by 20% every 15 minutes until one of the following
3. If the EUT fails open circuit, the test continues for an additional 15 minutes to ensure that another component of the EUT does not
http://www.teccor.com
+1 972-580-7777
and repeated at a reduced voltage and current just below the operating threshold of the secondary protectors.
uses a fuse as current limiting protection, the fuse may be bypassed and the short circuit current available adjusted to 135% of the
fuse rating.
occurs:
— Voltage reaches the maximum specified
— Current reaches 20 A or the wiring simulator opens
— EUT fails open circuit
create a fire, fragmentation, or electrical safety hazard.
(Notes 1, 2)
4 (Note 3)
5 (Note 4)
Test
1
2
3
Test
1
2
Applied Voltage, 60 Hz
Second Level AC Power Fault for Customer Premises Equipment
For customer premises equipment, the EUT is tested to the conditions presented in
Table 4.8 and connected to a circuit equivalent to that shown in Figure 4.2. During this test,
the wiring simulator cannot open. For equipment that uses premises type of wiring, the
wiring simulator is a 1.6 A Type MDQ fuse from Bussman. For equipment that is connected
by cable, the wiring simulator is a piece of 26-gauge copper wire.
120, 277
100-600
(V
Applied Voltage, 60 Hz
600
600
N/A
RMS
)
(Notes 2, 3)
(V
300
600
RMS
)
Short Circuit Current
per Conductor
2.2A at 600 V
(Note 5)
N/A
(A)
25
60
7
4 - 8
Source Impedance
20
20
W
Duration
SIDACtor
15 min
15 min
15 min
5 s
5 s
®
(Table 4.1, Figure 4.2)
Data Book and Design Guide
Test Connections
© 2002 Teccor Electronics
(Table 4.1, Figure 4.1)
(Note 1)
Test Connections
A
N/A
A
A
A
A