71M6521FE-IGT/F Maxim Integrated Products, 71M6521FE-IGT/F Datasheet - Page 76

• Manufacturer Part Number: 71M6521FE-IGT/F
• Description: IC ENERGY METER 32K FLASH 64LQFP
• Manufacturer: Maxim Integrated Products

Specifications of 71M6521FE-IGT/F

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

DIO_DIR1[7:6, 3:0]
DIO_DIR2 [5:3,2:1]
DIO_0[7:4,2:0]
DIO_1[7:6,3:0]
DIO_2[5:3,1:0]
DIO_EEX[1:0]
DIO_PV
DIO_PW
EEDATA[7:0]
EECTRL[7:0]
ECK_DIS
EQU[2:0]
EX_XFR
EX_RTC
EX_FWCOL
EX_PLL
FIR_LEN
Page: 76 of 107
SFR91
[7:6,3:0]
SFRA1
[5:3,2:1]
SFR80
[7:4,2:0]
SFR90
[7:6,3:0]
SFRA0
[5:3,1:0]
2008[7:6]
2008[2]
2008[3]
SFR9E
SFR9F
2005[5]
2000[7:5]
2002[0]
2002[1]
2007[4]
2007[5]
2005[4]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Programs the direction of pins DIO15-DIO14, DIO11-DIO8. 1 indi-
cates output. Ignored if the pin is not configured as I/O.
Programs the direction of pins DIO17-DIO16 (and DIO19-DIO21 for
the QFN package). 1 indicates output. Ignored if the pin is not con-
figured as I/O.
The value on the pins DIO7-DIO4 and DIO2-DIO1. Pins configured
as LCD will read zero. When written, changes data on pins confi-
gured as outputs. Pins configured as LCD or input will ignore write
operations. The pushbutton input PB is read on DIO_0[0].
The value on the pins DIO15-DIO14 and DIO11-DIO8. Pins con-
figured as LCD will read zero. When written, changes data on pins
configured as outputs. Pins configured as LCD or input will ignore
write operations.
The value on the pins DIO17-DIO16 (and DIO19-DIO21 for the QFN
package). Pins configured as LCD will read zero. When written,
changes data on pins configured as outputs. Pins configured as
LCD or input will ignore write operations.
When set, converts DIO4 and DIO5 to interface with external
EEPROM. DIO4 becomes SDCK and DIO5 becomes bi-directional
SDATA. LCD_NUM must be less than or equal to 18.
Causes VARPULSE to be output on DIO7, if DIO7 is configured as
output. LCD_NUM must be less than 15.
Causes WPULSE to be output on DIO6, if DIO6 is configured as
output. LCD_NUM must be less than 16.
Serial EEPROM interface data
Serial EEPROM interface control
Emulator clock disable. When one, the emulator clock is disabled.
gramming operations. If ECK_ENA is set, it should be done at
least 1000ms after power-up to give emulators and programming
devices enough time to complete an erase operation.
Specifies the power equation to be used by the CE.
Interrupt enable bits. These bits enable the XFER_BUSY, the
RTC_1SEC, the FirmWareCollision, and PLL interrupts. Note that if
one of these interrupts is to be enabled, its corresponding EX
enable bit must also be set. See the Interrupts section for details.
The length of the ADC decimation FIR filter.
When FIR_LEN=1, the ADC has 2.370370x higher gain.
DIO_EEX[1:0]
00
01
10
11
This bit is to be used with caution! Inadvertently
setting this bit will inhibit access to the part with the
ICE interface and thus preclude flash erase and pro-
1-384 cycles, 0-288 cycles
Function
Disable EEPROM interface
2-Wire EEPROM interface
3-Wire EEPROM interface
--not used--
71M6521DE/DH/FE Data Sheet
Rev 2