20-101-1207 Rabbit Semiconductor, 20-101-1207 Datasheet - Page 40
20-101-1207
Manufacturer Part Number
20-101-1207
Description
RCM4510W FCC CERTIFIED
Manufacturer
Rabbit Semiconductor
Type
Transceiver, 802.15.4/ZigBeer
Datasheet
1.20-101-1207.pdf
(118 pages)
Specifications of 20-101-1207
Frequency
2.4GHz
Wireless Frequency
29.49 MHz
For Use With/related Products
RCM4510W
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
316-1144
- Current page: 40 of 118
- Download datasheet (2Mb)
4.2 Serial Communication
The RCM4510W module does not have any serial driver or receiver chips directly on the
board. However, a serial interface may be incorporated on the board the RCM4510W is
mounted on. For example, the Prototyping Board has an RS-232 transceiver chip.
4.2.1 Serial Ports
There are six serial ports designated as Serial Ports A, B, C, D, E, and F. All six serial
ports can operate in an asynchronous mode up to the baud rate of the system clock divided
by 8. An asynchronous port can handle 7 or 8 data bits. A 9th bit address scheme, where
an additional bit is sent to mark the first byte of a message, is also supported.
Serial Port A is normally used as a programming port, but may be used either as an asyn-
chronous or as a clocked serial port once application development has been completed and
the RCM4510W is operating in the Run Mode.
Serial Port B is shared with the RCM4510W module’s asynchronous XBee RF module.
Flow control for the XBee RF module is provided from the Rabbit 4000 RxD+ and TxD–
Ethernet pins.
Serial Ports C and D can also be operated in the clocked serial mode. In this mode, a clock
line synchronously clocks the data in or out. Either of the two communicating devices can
supply the clock. Note that PD2 and PD0 provide the SCLKC and SCLKD outputs auto-
matically when Serial Ports C and D are set up as clocked serial ports.
Serial Ports E and F can also be configured as SDLC/HDLC serial ports. The IrDA proto-
col is also supported in SDLC format by these two ports. Serial Ports E and F must be con-
figured before they can be used. The sample program
in the
IOCONFIG_SWITCHECHO.C
Dynamic C
folder shows how to configure Serial Ports E
SAMPLES\RCM4500W\SERIAL
and F.
34
RabbitCore RCM4500W
Related parts for 20-101-1207
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: