ATMEGA128RZBV-8AU Atmel, ATMEGA128RZBV-8AU Datasheet - Page 35
![MCU ATMEGA1280/AT86RF230 100TQFP](/photos/6/70/67048/313-100-tqfp_sml.jpg)
ATMEGA128RZBV-8AU
Manufacturer Part Number
ATMEGA128RZBV-8AU
Description
MCU ATMEGA1280/AT86RF230 100TQFP
Manufacturer
Atmel
Series
ATMEGAr
Datasheets
1.ATMEGA640V-8CU.pdf
(38 pages)
2.ATMEGA640V-8CU.pdf
(444 pages)
3.AT86RF230-ZU.pdf
(98 pages)
Specifications of ATMEGA128RZBV-8AU
Frequency
2.4GHz
Data Rate - Maximum
2Mbps
Modulation Or Protocol
802.15.4 Zigbee
Applications
General Purpose
Power - Output
3dBm
Sensitivity
-101dBm
Voltage - Supply
1.8 V ~ 3.6 V
Data Interface
PCB, Surface Mount
Memory Size
128kB Flash, 4kB EEPROM, 8kB RAM
Antenna Connector
PCB, Surface Mount
Package / Case
100-TQFP
Wireless Frequency
2.4 GHz
Interface Type
JTAG, SPI
Output Power
3 dBm
For Use With
ATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK501 - ADAPTER KIT FOR 64PIN AVR MCUATSTK500 - PROGRAMMER AVR STARTER KIT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Operating Temperature
-
Current - Transmitting
-
Current - Receiving
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
ATmega128
11.3
11.4
11.5
11.6
2549MS–AVR–09/10
Rev. 2549K-01/07
Rev. 2549J-09/06
Rev. 2549I-07/06
Rev. 2549H-06/06
1.
2.
3.
4.
5.
6:
7.
8.
9.
10.
1.
2.
3.
4.
5.
6.
1.
2.
3.
1.
2.
3.
Updated
Updated
Updated
Updated
Updated Assembly code example in
after setting the ACBG bit or enabling the ADC, the user must always
allow the reference to start up before the output from the Analog Compar-
ator or ADC is used. To reduce power consumption in Power-down mode,
the user can avoid the three conditions above to ensure that the reference
is turned off before entering Power-down mode.” on page
Updated
Updated Bit description in
on page
Updated code example in
Updated
Updated
Updated
Updated code example in
Boot Section” on page
Updated
Updated
Updated
Updated
Added
Updated
page
page
on page
Updated
Updated
Updated
Added
160,
131,
“Data Retention” on page
Table 30-1 on page
116.
189.
Table 1-1 on page
“Pin Descriptions” on page
“Stack Pointer” on page
“Bit 1 – EEPE: EEPROM Programming Enable” on page
“EIMSK – External Interrupt Mask Register” on page
Figure 25-8 on page
“DC Characteristics” on page
“” on page
“Timer/Counter Prescaler” on page
“Device Identification Register” on page
“Signature Bytes” on page
“Instruction Set Summary” on page
“Fast PWM Mode” on page
“” on page
“OSCCAL – Oscillator Calibration Register” on page
Table 15-3 on page
Table 19-3 on page
Table 16-2 on page
46.
46.
109.
ATmega640/1280/1281/2560/2561
“USART Initialization” on page
371.
“Moving Interrupts Between Application and
“PCIFR – Pin Change Interrupt Flag Register”
3.
284.
129,
187,
148,
11.
16.
Table 15-6 on page
Table 19-6 on page 188
Table 16-4 on page
338.
“Thus, when the BOD is not enabled,
150.
7.
367.
186.
415.
303.
130,
159,
210.
63.
and
Table 15-8 on
Table 16-5 on
115.
50.
Table 19-8
36.
35