LMX9830SM/NOPB National Semiconductor, LMX9830SM/NOPB Datasheet - Page 35

• Manufacturer Part Number: LMX9830SM/NOPB
• Description: IC SRL PORT MOD BLUETOOTH 60FBGA
• Manufacturer: National Semiconductor

Specifications of LMX9830SM/NOPB

• Frequency: 2.4GHz
• Data Rate - Maximum: 704kbps
• Modulation Or Protocol: Bluetooth v2.0, Class 2
• Applications: PDA's, POS Terminals
• Power - Output: 0dBm
• Sensitivity: -80dBm
• Voltage - Supply: 2.5 V ~ 3.6 V
• Current - Receiving: 65mA
• Current - Transmitting: 65mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 60-FBGA
• Physical Interfaces: UART
• Data Rate: 704Kbps
• Operating Temperature Range: -40°C To +125°C
• Msl: MSL 4 - 72 Hours
• Supply Voltage Range: 1.6V To 3.6V
• Frequency Max: 2480MHz
• Termination Type: SMD
• Rohs Compliant: Yes
• Filter Terminals: SMD
• Frequency Min: 2402MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Compliant
• Other names: *LMX9830SM; *LMX9830SM/NOPB; LMX9830SM

Command
Get Default Audio Settings
Set Default Audio Settings
Set Event Filter
Get Event Filter
Read RSSI
Change UART Speed
Change UART Settings
Test Mode
Restore Factory Settings
Reset
Firmware Upgrade
Set Clock Frequency
Get Clock Frequency
Set PCM Slave Configuration
Write ROM Patch
Read Memory
Write Memory
Read NVS
Write NVS
Command
Set Clock and Baudrate
Enter Bluetooth Mode
Set Clock and Baudrate
Command
Set GPIO WPU
Get GPIO Input State
Set GPIO Direction
Set GPIO Output High
Set GPIO Output Low
Set GPIO WPU Confirm
Get GPIO Input States Confirm
Set GPIO Direction Confirm
Set GPIO Output High Confirm
Set GPIO Output Low Confirm
Set Clock and Baudrate Confirm
Enter Bluetooth Mode Confirm
Set Clock and Baudrate Confirm
Get Default Audio Settings Confirm
Set Default Audio Settings Confirm
Set Event Filter Confirm
Get Event Filter Confirm
Read RSSI Confirm
Change UART Speed Confirm
Change UART Settings Confirm
Test Mode Confirm
Restore Factory Settings Confirm
Dongle Ready
Set Clock Frequency Confirm
Get Clock Frequency Confirm
Set PCM Slave Configuration
Confirm
Write ROM Patch Confirm
Read Memory Confirm
Write Memory Confirm
Read NVS Confirm
Write NVS Confirm
TABLE 36. Local Hardware Commends
TABLE 38. GPIO Control commands
TABLE 37. Initialization Commands
Event
Event
Event
35
Get stored Default Audio Settings
Configure Default Settings for Audio Codec and Air Format,
stored in NVS
Configures the reporting level of the command interface
Get the status of the reporting level
Returns an indicator for the incoming signal strength
Set specific UART speed; needs proper ISEL pin setting
Change configuration for parity and stop bits
Enable Bluetooth, EMI test, or local loopback
Soft reset
Stops the bluetooth firmware and executes the In-system-
programming code
Write Clock Frequency setting in the NVS
Read Clock Frequency setting from the NVS
Write the PCM Slave Configuration in the NVS
Store ROM Patch in the SimplyBlue module
Read from the internal RAM
Write to the internal RAM
Read from the NVS (EEPROM)
Write to the NVS (EEPROM)
Write Baseband frequency and Baudrate used
Request SimplyBlue module to enter BT mode
Write Baseband frequency and Baudrate used
Enable/Disable weak pull up resistor on GPIOs
Read the status of the GPIOs
Set the GPIOs direction (Input, Ouput)
Set GPIOs Output to logical High
Set GPIOs Output to logical Low
Description
Description
Description
www.national.com