A16-1NRN Omron, A16-1NRN Datasheet - Page 137

• Manufacturer Part Number: A16-1NRN
• Description: NEON LAMP 110V RED FOR A16
• Manufacturer: Omron
• Type: Neon Lamp, 110 VoltsACr
• Series: A16r

Specifications of A16-1NRN

• Accessory Type: Neon Lamp Replacement
• Supply Voltage: 110V
• Base Type: Bi-Pin
• Colour: Red
• Current Rating: 1.5mA
• Svhc: No SVHC (15-Dec-2010)
• Illumination Colour: Red
• Operating Lifetime: 10000h
• Voltage Rating Vac: 110V
• Average Bulb Life: 1000
• Color: Red
• Illumination: Illuminated
• Height: 13 mm
• Illumination Color: Red
• Mounting Style: Snap In
• Termination Style: Tabs
• Lamp Base Type: Bi-Pin
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: A16 Series
• For Use With: Z1397 - SWTCH KNOB RND 3POS DPDT ILL REDZ1394 - SWTCH KNOB RND 2POS SPDT ILL REDZ1391 - SWTCH KNOB RND 2POS SPDT ILL REDZ1385 - SWITCH KNB RECT 3POS DPDT ILLZ1382 - SWITCH KNB RECT 2POS SPDT ILLZ1379 - SWITCH KNB RECT 2POS SPDT ILLZ1373 - SWITCH KNOB SQ 3-POS DPDT ILLZ1370 - SWITCH KNOB SQ 2-POS SPDT ILLZ1367 - SWITCH KNOB SQ 2-POS SPDT ILLZ1309 - SWITCH PB RND MOM DPDT ILLUM REDZ1305 - SWITCH PB RECT MOM DPDT ILLUMZ1301 - SWITCH PB SQ MOM DPDT ILLUM RED
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: A161NRN; Z1342

M2BJ-B
Precautions
Application Precautions
When power is supplied, there is an inrush current of up to 1 A. Con-
firm that this will not adversely affect operation or damage any
devices before using the M2BJ in application. There is no inrush
current with DC-only models (M2BJ-jjj-D).
Wiring
Perform soldering promptly and correctly at 30 W within 5 seconds
or at a temperature of 240°C within 3 seconds. Wait for one minute
after soldering before exerting any external force on the solder.
If flux is required, use non-corrosive rosin liquid. Ensure that the flux
does not penetrate the inside of the case.
In order to improve the reliability of the soldering and to prevent pat-
tern burnout, loop the wire through the terminal hole before solder-
ing.
In order to fit the terminal holes, use lead wires with a nominal cross-
sectional area of 0.25 mm
Operating Environment
Do not use the Buzzer in environments where foreign substances
may enter the sound outlet. Otherwise, the Buzzer may not sound.
Short-circuiting Jumper (M2BJ-BTH)
The Buzzer sounds continuously or intermittently depending on
how the short-circuiting bracket is attached to the case guide. When
the bracket is attached with the triangle on it facing direction A (PC
board side), the Buzzer sounds intermittently.
Cat. No. A046-E1-04
Correct Use
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Direction A
2
max.
Case guide
Bracket
Direction B
To produce continuous sounds, attach the bracket to the case guide
so that the triangle on the bracket faces direction B.
Volume Adjustment Mechanism (M2BJ-BH Only)
Adjust the volume by turning the control knob on the face of the
Buzzer using a screwdriver. Turn to the right to increase the volume
and turn to the left to decrease the volume.
Turn the control knob with a torque of 0.98 to 2.94 mN⋅m.
LED
Case guide
PC board
Bracket
Control knob
M2BJ-B
135