A16-1NRN Omron, A16-1NRN Datasheet - Page 162

• Manufacturer Part Number: A16-1NRN
• Description: NEON LAMP 110V RED FOR A16
• Manufacturer: Omron
• Type: Neon Lamp, 110 VoltsACr
• Series: A16r

Specifications of A16-1NRN

• Accessory Type: Neon Lamp Replacement
• Supply Voltage: 110V
• Base Type: Bi-Pin
• Colour: Red
• Current Rating: 1.5mA
• Svhc: No SVHC (15-Dec-2010)
• Illumination Colour: Red
• Operating Lifetime: 10000h
• Voltage Rating Vac: 110V
• Average Bulb Life: 1000
• Color: Red
• Illumination: Illuminated
• Height: 13 mm
• Illumination Color: Red
• Mounting Style: Snap In
• Termination Style: Tabs
• Lamp Base Type: Bi-Pin
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: A16 Series
• For Use With: Z1397 - SWTCH KNOB RND 3POS DPDT ILL REDZ1394 - SWTCH KNOB RND 2POS SPDT ILL REDZ1391 - SWTCH KNOB RND 2POS SPDT ILL REDZ1385 - SWITCH KNB RECT 3POS DPDT ILLZ1382 - SWITCH KNB RECT 2POS SPDT ILLZ1379 - SWITCH KNB RECT 2POS SPDT ILLZ1373 - SWITCH KNOB SQ 3-POS DPDT ILLZ1370 - SWITCH KNOB SQ 2-POS SPDT ILLZ1367 - SWITCH KNOB SQ 2-POS SPDT ILLZ1309 - SWITCH PB RND MOM DPDT ILLUM REDZ1305 - SWITCH PB RECT MOM DPDT ILLUMZ1301 - SWITCH PB SQ MOM DPDT ILLUM RED
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: A161NRN; Z1342

Mounting the Operation Unit on the
Panel
Insert the Operation Unit (Pushbutton, etc.) from the front surface of
the panel, insert the Lock Ring and the mounting nut from the termi-
nal side, then tighten the nut. Before tightening, check that the rubber
washer is present between the Pushbutton Unit and the panel.
When using a Legend Plate Frame, put one rubber washer each
between the Legend Plate Frame and the panel and between the
Operation Unit and the Legend Plate Frame. (One rubber washer will
be provided when one Legend Plate Frame is ordered.)
Align the Lock Ring with the groove in the casing, then insert the
Lock Ring so that its edge is located on the panel side.
Tighten the mounting nut at a torque of 0.98 to 1.96 N·m.
When using a Lock Ring, replace with the supplied Lock Ring, insert
the projecting part into the lock slot, and then tighten the mounting
nut.
When the panel cutout dimension is 25 dia., remove the supplied
rubber washer and mount the 25-dia. Ring as shown below. (Since
the A22Z-R25 is not attached to the main body, order separately.)
160
Hold here
Lock Ring
Panel
Mounting nut
Rubber washer
Panel
Lock Ring
22.3 dia.
22.3 dia.
22 dia.
25 dia.
25 dia.
Mounting nut
25-dia. Ring
Operation Unit
(A22Z-R25)
Pro-
jecting
part
Panel
Lock Ring
Mounting the Switch on the
Pushbutton Unit
Insert the Pushbutton Unit into the Switch Unit, aligning the arrow
mark inscribed on the Case with the lever on the Switch Blocks, then
move the lever in the direction indicated by the arrow in the following
figure.
Removing the Switch
Move the lever in the direction indicated by the arrow in the following
figure, then pull the Pushbutton Unit or the Switch Blocks.
Since the lever has a hole with an inside diameter of 6.5 mm, the
lever can be moved in the specified direction by inserting a screw-
driver into the hole and then moving the screwdriver.
Projection, Fall-guard
Grip and rotate the Color Cap with your fingers.
Mounting/Replacing the Color
Cap
Operation Unit
Arrow mark
Screwdriver
Lever