PIC18F24K22-I/SO Microchip Technology, PIC18F24K22-I/SO Datasheet - Page 262

• Manufacturer Part Number: PIC18F24K22-I/SO
• Description: IC PIC MCU 16KB FLASH 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F24K22-I/SO

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 19x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (0.300", 7.50mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 64MHz
• No. Of Timers: 7
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18(L)F2X/4XK22
REGISTER 15-4:
REGISTER 15-5:
DS41412A-page 262
bit 0
bit 7
Legend:
R = Readable bit
u = Bit is unchanged
‘1’ = Bit is set
bit 7-1
bit 0
Note 1: For daisy-chained SPI operation; allows the user to ignore all but the last received byte. SSPxOV is still
R/W-1
MSK7
2: This bit has no effect in Slave modes for which Start and Stop condition detection is explicitly listed as
3: The ACKTIM Status bit is active only when the AHEN bit or DHEN bit is set.
set when a new byte is received and BF = 1, but hardware continues to write the most recent byte to
SSPxBUF.
enabled.
DHEN: Data Hold Enable bit (I
1 = Following the 8th falling edge of SCLx for a received data byte; slave hardware clears the CKP bit
0 = Data holding is disabled
MSK<7:1>: Mask bits
1 = The received address bit n is compared to SSPxADD<n> to detect I
0 = The received address bit n is not used to detect I
MSK<0>: Mask bit for I
I
1 = The received address bit 0 is compared to SSPxADD<0> to detect I
0 = The received address bit 0 is not used to detect I
I
2
2
C Slave mode, 10-bit address (SSPxM<3:0> = 0111 or 1111):
C Slave mode, 7-bit address, the bit is ignored
R/W-1
MSK6
of the SSPxCON1 register and SCLx is held low.
SSPxCON3: SSPx CONTROL REGISTER 3 (CONTINUED)
SSPxMSK: SSPx MASK REGISTER
W = Writable bit
x = Bit is unknown
‘0’ = Bit is cleared
R/W-1
MSK5
2
C Slave mode, 10-bit Address
2
C Slave mode only)
R/W-1
MSK4
Preliminary
U = Unimplemented bit, read as ‘0’
-n/n = Value at POR and BOR/Value at all other Resets
R/W-1
MSK3
2
2
C address match
C address match
R/W-1
MSK2
 2010 Microchip Technology Inc.
2
2
C address match
C address match
R/W-1
MSK1
R/W-1
MSK0
bit 0