AD5235BRU25-RL7 Analog Devices Inc, AD5235BRU25-RL7 Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD5235BRU25-RL7
Manufacturer Part Number
AD5235BRU25-RL7
Description
IC DGTL POT DUAL 1024POS 16TSSOP
Manufacturer
Analog Devices Inc
Specifications of AD5235BRU25-RL7
Rohs Status
RoHS non-compliant
Taps
1024
Resistance (ohms)
25K
Number Of Circuits
2
Temperature Coefficient
35 ppm/°C Typical
Memory Type
Non-Volatile
Interface
4-Wire SPI Serial
Voltage - Supply
3 V ~ 5.5 V, ±2.25 V ~ 2.75 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-TSSOP (0.173", 4.40mm Width)
Number Of Elements
2
# Of Taps
1024
Resistance (max)
25KOhm
Power Supply Requirement
Single/Dual
Interface Type
Serial (4-Wire/SPI)
Single Supply Voltage (typ)
3.3/5V
Dual Supply Voltage (typ)
±2.5V
Single Supply Voltage (min)
3V
Single Supply Voltage (max)
5.5V
Dual Supply Voltage (min)
±2.25V
Dual Supply Voltage (max)
±2.75V
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
16
Lead Free Status / RoHS Status
Not Compliant
Other names
AD5235BRU25-RL7
AD5235BRU25-RL7TR
AD5235BRU25-RL7TR
AD5235
ADVANCED CONTROL MODES
The AD5235 digital potentiometer includes a set of user
programming features to address the wide number of
applications for these universal adjustment devices.
Key programming features include the following:
•
•
•
•
•
Linear Increment and Decrement Instructions
The increment and decrement instructions (Instruction 14,
Instruction 15, Instruction 6, and Instruction 7) are useful for
linear step adjustment applications. These commands simplify
microcontroller software coding by allowing the controller to
send just an increment or decrement command to the device.
The adjustment can be individual or in a ganged potentiometer
arrangement where both wiper positions are changed at the
same time.
For an increment command, executing Instruction 14
automatically moves the wiper to the next resistance segment
position. The master increment command, Instruction 15,
moves all resistor wipers up by one position.
Logarithmic Taper Mode Adjustment
Four programming instructions produce logarithmic taper
increment and decrement of the wiper position control by
an individual potentiometer or by a ganged potentiometer
arrangement where both wiper positions are changed at the
same time. The 6 dB increment is activated by Instruction 12
and Instruction 13, and the 6 dB decrement is activated by
Instruction 4 and Instruction 5. For example, starting with the
wiper connected to Terminal B, executing 11 increment
instructions (Command Instruction 12) moves the wiper in 6 dB
steps from 0% of the R
position of the AD5235 10-bit potentiometer. When the wiper
position is near the maximum setting, the last 6 dB increment
instruction causes the wiper to go to the full-scale 1023 code
position. Further 6 dB per increment instructions do not
change the wiper position beyond its full scale (see Table 8).
The 6 dB step increments and 6 dB step decrements are achieved
by shifting the bit internally to the left or right, respectively. The
following information explains the nonideal ±6 dB step adjustment
under certain conditions. Table 8 illustrates the operation of the
shifting function on the RDAC register data bits. Each table row
represents a successive shift operation. Note that the left-shift
12 and 13 instructions were modified such that, if the data in
the RDAC register is equal to zero and the data is shifted left,
Scratchpad programming to any desirable values
Nonvolatile memory storage of the scratchpad RDAC
register value in the EEMEM register
Increment and decrement instructions for the RDAC wiper
register
Left and right bit shift of the RDAC wiper register to
achieve ±6 dB level changes
26 extra bytes of user-addressable nonvolatile memory
BA
(Terminal B) position to 100% of the R
Rev. C | Page 18 of 28
BA
the RDAC register is then set to Code 1. Similarly, if the data in
the RDAC register is greater than or equal to midscale and the data
is shifted left, then the data in the RDAC register is automatically
set to full scale. This makes the left-shift function as ideal a
logarithmic adjustment as possible.
The Right-Shift 4 instruction and Right-Shift 5 instruction are
ideal only if the LSB is 0 (ideal logarithmic = no error). If the
LSB is 1, the right-shift function generates a linear half-LSB
error, which translates to a number-of-bits dependent logarithmic
error, as shown in Figure 42. Figure 42 shows the error of the odd
numbers of bits for the AD5235.
Table 8. Detail Left-Shift and Right-Shift Functions for 6 dB
Step Increment and Decrement
Left-Shift (+6 dB/Step)
00 0000 0000
00 0000 0001
00 0000 0010
00 0000 0100
00 0000 1000
00 0001 0000
00 0010 0000
00 0100 0000
00 1000 0000
01 0000 0000
10 0000 0000
11 1111 1111
11 1111 1111
Actual conformance to a logarithmic curve between the data
contents in the RDAC register and the wiper position for each
Right-Shift 4 command and Right-Shift 5 command execution
contains an error only for odd numbers of bits. Even numbers of
bits are ideal. Figure 42 shows plots of log error [20 × log
(error/code)] for the AD5235. For example, Code 3 log error = 20 ×
log
is more significant at the lower codes (see Figure 42).
10
(0.5/3) = −15.56 dB, which is the worst case. The log error plot
Figure 42. Log Error Conformance for Odd Numbers of Bits Only
–20
–40
–60
–80
0
0
0.1
0.2
(Even Numbers of Bits Are Ideal)
CODE (From 1 to 1023 by 2.0 × 10
0.3
0.4
0.5
Right-Shift(–6 dB/Step)
11 1111 1111
01 1111 1111
00 1111 1111
00 0111 1111
00 0011 1111
00 0001 1111
00 0000 1111
00 0000 0111
00 0000 0011
00 0000 0001
00 0000 0000
00 0000 0000
00 0000 0000
0.6
0.7
0.8
3
)
0.9
1.0
10
1.1