PVG3A103C01R00 Murata, PVG3A103C01R00 Datasheet - Page 50

Trimmer Resistors - SMD 10Kohms Sealed 3mm Single turn

PVG3A103C01R00

Manufacturer Part Number
PVG3A103C01R00
Description
Trimmer Resistors - SMD 10Kohms Sealed 3mm Single turn
Manufacturer
Murata
Series
PVG3Ar
Type
Trimmerr
Datasheet

Specifications of PVG3A103C01R00

Resistance
10 KOhms
Power Rating
0.25 Watt (1/4 Watt)
Operating Temperature Range
- 55 C to + 125 C
Element Type
Cermet
Dimensions
3.4 mm W x 3.6 mm L x 2 mm H
Product
Single-Turn Trimmer Potentiometers
Termination Style
SMD/SMT
Tolerance
20 %
Number Of Turns
1
Taper
Linear
Temperature Coefficient
+/- 150 PPM / C
Tolerance (+ Or -)
20%
Technology
Cermet
Mounting Style
Surface Mount
Operating Temp Range
-55C to 125C
Failure Rate
Not Required
Shaft Diameter (mm)
2.2mm
Product Diameter (mm)
Not Requiredmm
Product Length (mm)
3.6mm
Product Height (mm)
2mm
Product Depth (mm)
3.6mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PVG3A103C01R00
Manufacturer:
MURATA
Quantity:
240 000
8
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1
48
No.
The tests and measurements should be conducted under the condition of 15 to 35°C of temperature, 25 to 75% of relative humidity and 86 to 106 kpa of
atmospheric pressure unless otherwise specified. If questionable results occur that have been measured in accordance with the above mentioned
conditions, the tests and measurements should be conducted under the condition of 25±2°C of temperature, 45 to 55% of relative humidity and 86 to
106 kpa of atmospheric pressure.
SMD Open Type (PVZ2/A2/Z3)/SMD Sealed Type (PVM4A_C01 Series) Specifications and Test Methods
1
2
3
4
5
6
7
8
9
Specifications and Test Methods
Residual Resistance
Contact Resistance
Humidity Exposure
High Temperature
Exposure
Humidity Load Life
Load Life
Temperature Cycle
Temperature Coefficient of
Resistance
Rotational Life
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Position the contact arm at the extreme counterclockwise limit of mechanical travel and measure the resistance
between the contact arm and the corresponding end terminal. Then, position the contact arm at the extreme clock-
wise limit of mechanical travel and measure the resistance between the contact arm and the corresponding end ter-
minal. During this test, take suitable precautions to ensure that the rated current of the resistance element is not
exceeded.
Contact resistance variation should be measured with the measuring circuit shown below, or its equivalent. The
operating wiper should be rotated in both directions through 90% of the actual effective-electrical travel for a total of
6 cycles.
The rate of rotation of the operating wiper should be such that the wiper completes 1 count in determining whether or
not a contact resistance variation is observed at least twice in the same location. The test current should follow the
value given in Table 2 unless otherwise limited by the power rating.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the poten-
tiometer should be placed in a chamber at 40±2°C and 90 - 95% without loading for 500±12 hours.
The resistance value should be measured after keeping the potentiometer in a room for 5±1/6 hours.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the poten-
tiometer should be placed in a chamber at 70±2°C without loading for 500±12 hours. The resistance value should be
measured after keeping the potentiometer in a room for 1.5±1/6 hours.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the poten-
tiometer should be placed in a chamber at 40±2°C and 90 - 95% with loading the 1/2 rated voltage between #1 and
#2 terminals, intermittently 1.5 hours ON and 0.5 hours OFF for 1000±12 hours.
The resistance value should be measured after keeping the potentiometer in a room for 5±1/6 hours.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the poten-
tiometer should be placed in a chamber at 70±2°C (50±2°C for PVZ) with loading the 1/2 rated voltage between #1
and #2 terminals, intermittently 1.5 hours ON and 0.5 hours OFF for 1000±12 hours. The resistance value should be
measured after keeping the potentiometer in a room for 1 to 2 hours.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the poten-
tiometer should be subjected to Table 3, Table 4 temperature for 5 cycles. The resistance value should be measured
after keeping the potentiometer in a room for 1 to 2 hours.
The trimmer potentiometer should be subjected to each of the following temperatures (see Table 5, Table 6) for 30
to 40 minutes. The resistance value should be measured in the chamber.
TCR=
Note*: Norm temp.
The wiper should be rotated over 90% of the effective rotational angle without loading at a speed of 10 cycles per
minute, for 10 cycles continuously. The resistance value should be measured after keeping the potentiometer in a
room for 10±5 minutes.
Resistance R (ohm)
Temp. (°C)
Time (min.)
Temp. (°C) +25±2
Sequence
Sequence
Standard Total
100kVR
100VRF10k
10kVRF100k
Table 2: Test current for CRV
R
T
T
R
R
1
R
1
2
1
2
(T
2
: Reference temperature in degrees celsius
: Test temperature in degrees celsius
: Resistance at reference temperature in ohm
: Resistance at test temperature in ohm
– R
2
-25±3
– T
30±3
1
1*
1
Table 3: PVZ
Table 5: PVZ
1
)
Z 10
10 max.
+25±2
-25±3
2
2
6
Test Current
100µA max.
20mA max.
(ppm/°C)
1mA max.
+85±3
+25±2
30±3 10 max.
3*
3
+25±2
+85±3
4
4
Test Methods
Constant Current
Source
(Test current
shown in Table 2)
Time (min.)
Temp. (°C)
Temp. (°C) +25±2
Sequence
Sequence
Rx : Trimmer Potentiometer
Oscilloscope bandwidth: 100Hz to 50kHz
Table 4: PVA2/PVM4A---C01
Table 6: PVA2/PVM4A---C01
Figure 1: CRV measuring circuit
#1
-55±3
Proofread
Resistence
30±3
1*
1
#2
Rx
#3
10 max.
+25±2
-55±3
2
2
+125±3 +25±2
+25±2 +125±3
30±3 10 max.
3*
3
AC
Amplifier
4
4
Oscilloscope
R50E.pdf
08.8.26

Related parts for PVG3A103C01R00