ISL12022IBZ-T7A Intersil, ISL12022IBZ-T7A Datasheet - Page 10

• Manufacturer Part Number: ISL12022IBZ-T7A
• Description: IC RTC/CALENDAR TEMP SNSR 8SOIC
• Manufacturer: Intersil
• Type: Clock/Calendarr

Specifications of ISL12022IBZ-T7A

• Memory Size: 128B
• Time Format: HH:MM:SS (12/24 hr)
• Date Format: YY-MM-DD-dd
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Power Failure Detection
The ISL12022 provides a Real Time Clock Failure Bit
(RTCF) to detect total power failure. It allows users to
determine if the device has powered up after having lost all
power to the device (both V
Brownout Detection
The ISL12022 monitors the V
provides warning if the V
levels. There are six (6) levels that can be selected for the
trip level. These values are 85% below popular V
The LVDD bit in the Status Register will be set to “1” when
brownout is detected. Note that the I
active unless the Battery V
Battery Level Monitor
The ISL12022 has a built in warning feature once the
Back-up battery level drops first to 85% and then to 75% of
the battery’s nominal V
drops to between 85% and 75%, the LBAT85 bit is set in the
status register. When the level drops below 75%, both
LBAT85 and LBAT75 bits are set in the status register.
The battery level monitor is not functional in battery backup
mode. In order to read the monitor bits after powering up
V
TSE bit to "1" (BETA register), and then read the bits.
There is a Battery Time Stamp Function available. Once the
V
RTC time/date are written into the TSV2B register. This
information can be read from the TSV2B registers to
discover the point in time of the V
are multiple power-down cycles before reading these
registers, the first values stored in these registers will be
retained. These registers will hold the original power-down
value until they are cleared by setting CLRTS = 1 to clear the
registers.
The normal power switching of the ISL12022 is designed to
switch into battery-backup mode only if the V
lost. This will ensure that the device can accept a wide range
of backup voltages from many types of sources while reliably
switching into backup mode.
Note that the ISL12022 is not guaranteed to operate with
V
than this minimum, correct operation of the device,
especially after a V
The minimum V
that, the SRAM may be corrupted when V
Real Time Clock Operation
The Real Time Clock (RTC) uses an external 32.768kHz
quartz crystal to maintain an accurate internal representation
of second, minute, hour, day of week, date, month, and year.
The RTC also has leap-year correction. The clock also
DD
DD
BAT
, instigate a battery level measurement by setting the
is low enough to enable switchover to the battery, the
< 1.8V. If the battery voltage is expected to drop lower
BAT
DD
to insure SRAM is stable is 1.0V. Below
power-down cycle, is not guaranteed.
BAT
DD
TRIP
level. When the battery voltage
DD
level drops below prescribed
10
DD
and V
levels are reached.
level continuously and
DD
2
BAT
power-down. If there
C serial bus remains
).
DD
power resumes.
DD
power is
DD
levels.
ISL12022
corrects for months having fewer than 31 days and has a bit
that controls 24-hour or AM/PM format. When the ISL12022
powers up after the loss of both V
not begin incrementing until at least one byte is written to the
clock register.
Single Event and Interrupt
The alarm mode is enabled via the MSB bit. Choosing single
event or interrupt alarm mode is selected via the IM bit. Note
that when the frequency output function is enabled, the
alarm function is disabled.
The standard alarm allows for alarms of time, date, day of
the week, month, and year. When a time alarm occurs in
single event mode, the IRQ/F
the alarm status bit (ALM) will be set to “1”.
The pulsed interrupt mode allows for repetitive or recurring
alarm functionality. Hence, once the alarm is set, the device
will continue to alarm for each occurring match of the alarm
and present time. Thus, it will alarm as often as every minute
(if only the nth second is set) or as infrequently as once a
year (if at least the nth month is set). During pulsed interrupt
mode, the IRQ/F
the alarm status bit (ALM) will be set to “1”.
The ALM bit can be reset by the user or cleared automatically
using the auto reset mode (see ARST bit). The alarm function
can be enabled/disabled during battery-backup mode using
the FOBATB bit. For more information on the alarm, please
see “ALARM Registers (10h to 15h)” on page 19.
Frequency Output Mode
The ISL12022 has the option to provide a clock output signal
using the IRQ/F
output mode is set by using the FO bits to select 15 possible
output frequency values from 1/32Hz to 32kHz. The
frequency output can be enabled/disabled during
battery-backup mode using the FOBATB bit.
General Purpose User SRAM
The ISL12022 provides 128 bytes of user SRAM. The SRAM
will continue to operate in battery-backup mode. However, it
should be noted that the I
battery-backup mode.
I
The ISL12022 has an I
access to the control and status registers and the user
SRAM. The I
industry I
signal (SDA) and a clock signal (SCL).
Oscillator Compensation
The ISL12022 provides both initial timing correction and
temperature correction due to variation of the crystal
oscillator. Analog and digital trimming control is provided for
initial adjustment, and a temperature compensation function
is provided to automatically correct for temperature drift of
2
C Serial Interface
2
C serial bus protocols using a bi-directional data
2
C serial interface is compatible with other
OUT
OUT
open drain output pin. The frequency
pin will be pulled low for 250ms and
2
C serial bus interface that provides
2
C bus is disabled in
OUT
DD
pin will be pulled low and
and V
BAT
, the clock will
June 23, 2009
FN6659.2