1-2154009-6 TE Connectivity, 1-2154009-6 Datasheet
1-2154009-6
Specifications of 1-2154009-6
Related parts for 1-2154009-6
1-2154009-6 Summary of contents
Page 1
... All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters. Unless NOTE otherwise specified, dimensions have a tolerance of ±0.20 and angles have a tolerance of ±2°. Figures and illustrations i are for identification only and are not drawn to scale. 1. INTRODUCTION The NEVALO Interconnect System is designed complete LED lighting interconnect solution ...
Page 2
... Updated document to corporate requirements • Added new artwork to Figures and 11 • Changed, added, or deleted text in Section 1, INTRODUCTION; Paragraphs 3.7, 3.8, 3.9, 3.9.B.3, 3.10.A; and Section 4, QUALIFICATIONS • Added new information to table in Figure 10 2.2. Customer Assistance Reference Part Number 2154234 and Product Code L895 are representative numbers of the NEVALO Interconnect System ...
Page 3
... TE Representative for current tool recommendations for cutting and notching of cables. A notching procedure is required when a NEVALO Feed-Thru connector is used. Use cable notching tool 2119990-1 to NOTE ensure proper notch size and length. Contact the Product Information Center number at the bottom of page 1 for specific i information on this process or refer to hand tool instruction sheet. ...
Page 4
... B. Tolerance Maximum allowable bow of the pc board shall be 0.05 mm over the length of the connector. C. Pads The pc board circuit pads must be solderable in accordance with Test Specification 109-11. D. Layout The pc board layout must be designed using the dimensions provided on the customer drawing for the specific connector. Reference sample of the recommended pc board layout is shown Figure 4. ...
Page 5
... NEVALO SMT Clip NEVALO Driver Header 2.50 ± 1.15 0.05 0. 2.80 9.85 -C- ± 1.70 0.05 0. Rev B -B- 1. 1.65 2X 3.00 2X 6.90 2X Figure 4 114-13290 ±0.08 ± 2.80 0.05 0. ± 3.75 0.05 0. 6.85 ± 0.05 0. ...
Page 6
... B. Connectors with SMT Contacts 1. Solderability The pc board pads must be solderable in accordance with Test Specification 109-11 (Test Method A, non-activated rosin flux) and all other requirements for surface mount contacts specified in this document. 2. Solder Paste Characteristics 1. Alloy type shall be SAC 305; Sn 96.5/Ag 3.0/Cu 0.5. ...
Page 7
... SOLDERING PROCESS IR The lead-free reflow profile is shown in Figure 7. 3.10. Connector Placement A. Position Optimally, the clip solder feet should be centered on the pads; ever, slight misalignment is permissible. Refer to Figure 8. The pegs of the driver header should be inserted into the holes in the pc board to ensure proper alignment. ...
Page 8
... QUALIFICATIONS The NEVALO Interconnect System has been Component Recognized to US and Canadian standards (UL1977 and CSA C22.2 No. 182.3) by Underwriters Laboratories Inc. (UL) File E28476 Vol 107 dated 2011 02 25. 5. TOOLING This section provides a selection of tools for various application requirements. Modified designs and additional tooling concepts may be available to meet other application requirements ...
Page 9
... NEVALO Interconnect System. Hand crimping tools are designed for prototype and low-volume applications. Instruction sheets covering tool setup and operation. See Figure 10. CONNECTOR TYPE DIE SET Feed-Thru Multi-Nest Straight 2161080-1 Terminator Right-Angle Right-Angle 2161085-1 Bus-to-Wire Tooling not required to unmate connectors from clip ...
Page 10
... DRIVER WIRES SHOULD BE VISIBLE THROUGH VIEWING HOLES IN BUS- TO-WIRE CONNECTOR RIBBON STRIPE AND CONNECTOR STRIPES SHOULD ALL BE IN ALIGNMENT Rev B FIGURE 11. VISUAL AID (CONT’D) 114-13290 ALL LATCHES SHOULD BE FULLY CLOSED ...
Page 11
... ALL LATCHES SHOULD BE FULLY CLOSED NOT FULLY CLOSED Rev B FIGURE 11. VISUAL AID (CONT’D) 114-13290 FULLY CLOSED ...
Page 12
... Care must be taken when mating or CAUTION unmating connectors to/from clip. ! Rev B FIGURE 11. VISUAL AID (END) 114-13290 CLIP LATCH MUST BE FULLY CLOSED PAST HOUSING BUMP ...