ISL6140/41EVAL1Z Intersil, ISL6140/41EVAL1Z Datasheet
ISL6140/41EVAL1Z
Specifications of ISL6140/41EVAL1Z
Related parts for ISL6140/41EVAL1Z
ISL6140/41EVAL1Z Summary of contents
Page 1
... C1 = 150nF (25V 3.3nF (100V IRF530 (100V, 17A, 0.11Ω 100µF (100V equivalent load TM electronic circuit breaker distinguishes | Intersil (and design registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved Endura™ trademark of Intersil Americas Inc. AN1020 ...
Page 2
... ISL6141/51 Hot Plug Controller, Document # FN9079 • ISL6142/52 Hot Plug Controller, Document # FN9086 • ISL6142/52 EVAL1 Board Set, Document # AN1000 • ISL6116 Hot Plug Controller, Document # FN4778 NOTE: See www.intersil.com/hotplug for more information. BUS BOARD Eval Board • Three-board set with edge connectors to simulate live plug-ins • ...
Page 3
... Edge connector pins plug into Control board CONTROL Board (IC Hot-Plug; Fig. 7) • 2 Identical hot plug channels - Compare Intersil ISL6140 (L) to ISL6141 (L), or replace the units with the ISL6150/51 and evaluate the active high power good output function. - Change components for alternate applications • ...
Page 4
All Power off. 3. Connect the gray wire to GND (or most positive voltage); connect the -VINA (violet) and -VINB (blue) wire(s) to the negative 48V supply (or the most negative voltage). 4. Plug the 3 boards together; from ...
Page 5
... Required Components (Same for both A and B channels; See Fig. 4 and the ISL6140 (L) or ISL6141 (L) Intersil hot plug controller IC. The ISL6141 is an enhanced version of the ISL6140 and is pin for pin compatible. The functional differences are summarized on page 1.The ISL6150 and ISL6151 function and perform the same as the ISL6140 and ISL6141 respectively, with the exception of their power good outputs which are active high ...
Page 6
Over-Current load capacitor that can be placed on the CONTROL board (in addition to the three cap footprints on the LOAD board). It can be ...
Page 7
LOAD Board Labels (See Fig. 9) CAUTION HOT The load resistors are mounted on the bottom of the LOAD board, but the heat can be felt through the top of the board. Be careful how you handle the board, especially ...
Page 8
ISL6140/41 EVAL boards BUS (Input) top of board top of board top of board -VINA board bottom GND top of board -VINB (Two identical channels (A/B) on board; all components have a suffix A or B). GND GND R4 (short ...
Page 9
ISL6140/41 EVAL boards LOAD (Output) 3 edge connector pins; top 6 edge connector pins; bottom (4 GND; 2 PWRGD or PWRGD) 3 edge connector pins; top 9 -VOUTA A C11A LOAD C12A TPPGA C13A GND C11B TPPGB C12B B C13B ...
Page 10
Bill Of Material Component Name CONTROL BOARD BOM U1 A/B ISL6140 (A); ISL6141 (B) Q1 A/B IRF530 or equivalent Q2 A/B Optional FET Q3 A/B Optional FET R1 A/B Current Sense Resistor R1_alt A/B Current Sense Resistor (alternate) R2 A/B ...
Page 11
Component Name D11 A/B Red LED SW11 A/B Load Slide Switch SW12 A/B C11 A/B Optional Load Capacitors C12 A/B C13 A/B Note: Surface Mount Resistors are 1/10W unless otherwise noted Note: DNP = Do Not Populate 11 TABLE 2. ...
Page 12
Component Placement and Labels NOTE: D11B NOT LABELED 12 ISL6140/41 FIGURE 9. LOAD BOARD ISL6140/41 FIGURE 10. CONTROL BOARD ...
Page 13
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...