ISL6140/41EVAL1Z Intersil, ISL6140/41EVAL1Z Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL6140/41EVAL1Z
Manufacturer Part Number
ISL6140/41EVAL1Z
Description
EVAL BOARD 1 FOR ISL6140/41
Manufacturer
Intersil
Specifications of ISL6140/41EVAL1Z
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
• The boards can be used in a positive supply configuration,
• Boards are set for 54V max operation (using
• Typical load is a -48V to 5V brick regulator.
BUS board (Input -48V Power; Fig. 6)
• Multiple large holes for soldering wires, posts, pins, etc.
• Holes for optional input caps
• Edge connector pins plug into Control board
CONTROL Board (IC Hot-Plug; Fig. 7)
• 2 Identical hot plug channels
• Red “FAULT” LED (Power Good; for ISL6140/41 only);
• Push-button Switch for Over-Current latch reset
• Footprints for 3 FET outlines; D2PAK, SO-8, SOT-223
• Short pin connection for UV lockout
• Test point for each IC pin
• Small bread-board area for adding user circuitry
• Approximate minimum board area highlighted
• Board application options (See “Optional Components”
connections (on power supplies or oscilloscopes) that
don’t match the user’s GND.
as long as the user renames (mentally or physically) the
signals (the GND will become the positive supply, and -
VINA and -VINB will become the new GND). Here, both
supplies must be the same voltage.
Over-Voltage shutdown) to protect the load resistors.
Users have the option to change components and
substitute alternate loads. UV is set at 37V.
for input power (-48V and GND typical)
- Compare Intersil ISL6140 (L) to ISL6141 (L), or replace
- Change components for alternate applications
jumper to disconnect it (if it interferes with logic level)
section)
- Plated through holes for adding load capacitors
- Footprints for RC filter on VDD
- Footprints for RC delay on Over-Current shutdown
- Footprint for DRAIN protection diodes
the units with the ISL6150/51 and evaluate the active
high power good output function.
(applicable for ISL6140/50)
BUS
-VINA
GND
-VINB
FIGURE 2. LEDs AND TEST POINTS
SW1A
SW1B
CONTROL
D5A LED
D5B LED
3
A ON LED
TPPGA
TPPGB
LOAD
TPA
B ON LED
TPB
LOAD Board (R and C Loads; Fig 8)
• Edge connector pins plug into Control board
• Typical Load current is <100mA (limited by power
• Two load resistors for each channel; one ~80mA, 2nd
• Switches to connect the loads in and out
• Multiple holes for soldering wires, pins, posts, for external
• Holes for optional load caps
• Power Good signal from each channel brought over
• LED Channel “ON” indication
-48V Hook-Up Instructions
NOTE: If the user substitutes higher current external loads, the
power supply capability would need to be increased accordingly.
1. Get one (or two) -48V power supplies (~0.25A current
- Footprint for Over-Voltage clamping suppressor
- Green LED for Power Good OK (ISL6140/41 only)
- Alternate Sense Resistor (0.02Ω) included
dissipation of the load resistors); Over-Current trip is
~185mA.
~160mA; in parallel ~240mA (Over-Current).
output load connections (brick regulators are too big and
varied to include on the board).
through edge connector, for use with brick regulator;
available on test pins.
needed per channel; 0.5A total). A positive supply can
also be used as long as the user keeps the polarities
correct. The two channels can share one voltage supply,
can each have their own supply, or can even have two
different voltages (no special power-up sequence is
needed). If only one channel is being tested, the other
can be left unconnected. The following instructions are
the same for both channels. As shown in Fig. 3, A1 is an
optional ammeter to measure current; V1 is an Voltmeter
to measure power supply voltage, and V2 is a voltmeter
to look at other signals. Note that the voltmeters are
referenced to the negative supply rail.
to -VINA
(violet)
PS1
+
-
FIGURE 3. HOOK UP
A1
to GND (gray) (V2)
to -VINB
(blue)
+
-
V1
V2
+
-