S29AL016J70TFI020 Spansion Inc., S29AL016J70TFI020 Datasheet - Page 53

• Manufacturer Part Number: S29AL016J70TFI020
• Description: IC, FLASH, 16MBIT, 70NS, TSOP-48
• Manufacturer: Spansion Inc.

Specifications of S29AL016J70TFI020

• Memory Type: Flash
• Memory Size: 16Mbit
• Memory Configuration: 2M X 8 / 1M X 16
• Ic Interface Type: CFI, Parallel
• Access Time: 70ns
• Supply Voltage Range: 2.7 To 3.6 V
• Memory Case Style: TSOP
• Cell Type: NOR
• Density: 16Mb
• Access Time (max): 70ns
• Interface Type: Parallel
• Boot Type: Bottom
• Address Bus: 21/20Bit
• Operating Supply Voltage (typ): 3/3.3V
• Operating Temp Range: -40C to 85C
• Package Type: TSOP
• Program/erase Volt (typ): 2.7 to 3.6V
• Sync/async: Asynchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8/16Bit
• Number Of Words: 2M/1M
• Supply Current: 12mA
• Mounting: Surface Mount
• Pin Count: 48
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

18. Erase and Programming Performance
19. TSOP and BGA Pin Capacitance
February 18, 2010 S29AL016J_00_10
Notes
1. Typical program and erase times assume the following conditions: 25
2. Under worst case conditions of 90°C, V
3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes program faster
4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See
6. The device has a minimum erase and program cycle endurance of 100,000 cycles per sector.
Notes
1. Sampled, not 100% tested.
2. Test conditions T
Sector Erase Time
Chip Erase Time
Byte Programming Time
Word Programming Time
Chip Programming Time
(Note 3)
Parameter Symbol
than the maximum program times listed.
on page 35
C
C
C
C
OUT
IN2
IN3
IN
for further information on command definitions.
Parameter
A
= 25°C, f = 1.0 MHz.
Byte Mode
Word Mode
D a t a
Control Pin Capacitance
Parameter Description
WP# Pin Capacitance
Output Capacitance
Input Capacitance
CC
S h e e t
= 2.7 V, 1,000,000 cycles.
Typ
S29AL016J
21.6
(Note 1)
0.5
6.3
16
6
6
Max
°
C, V
Test Setup
150
150
160
120
V
(Note 2)
10
V
V
V
OUT
CC
IN
IN
IN
= 3.0 V, 100,000 cycles, checkerboard data pattern.
= 0
= 0
= 0
= 0
Unit
Package
µs
µs
TSOP
TSOP
TSOP
TSOP
s
s
s
s
BGA
BGA
BGA
BGA
Excludes 00h programming
prior to erasure
Excludes system level
overhead
Typ
4.5
4.5
8.5
8.5
4
4
5
5
Comments
(Note 5)
Max
5.5
5.5
6.5
6.5
(Note 4)
10
10
6
6
Table 10.1
Unit
pF
53