BD2202G-TR Rohm Semiconductor, BD2202G-TR Datasheet - Page 14

• Manufacturer Part Number: BD2202G-TR
• Description: POWER MANAGEMENT SWITCH IC, SSOP5
• Manufacturer: Rohm Semiconductor
• Series: -r
• Type: High Side Switchr

Specifications of BD2202G-TR

• Primary Input Voltage: 3.6V
• No. Of Outputs: 1
• Output Voltage: 3.9V
• Output Current: 200mA
• Voltage Regulator Case Style: SSOP
• No. Of Pins: 5
• Operating Temperature Range: -25°C To +85°C
• Svhc: No SVHC
• Input Type: Non-Inverting
• Number Of Outputs: 1
• On-state Resistance: 150 mOhm
• Current - Output / Channel: 200mA
• Current - Peak Output: 400mA
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -25°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: SC-74A, SOT-753
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Cautions on use
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
Absolute Maximum Ratings
Operating conditions
Reverse connection of power supply connector
Power supply line
GND voltage
Short circuit between terminals and erroneous mounting
Operation in strong electromagnetic field
Inspection with set PCB
Input terminals
These conditions represent a range within which characteristics can be provided approximately as expected. The
electrical characteristics are guaranteed under the conditions of each parameter.
Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal. At
the same time, in order to use an electrolytic capacitor, thoroughly check to be sure the characteristics of the capacitor to
be used present no problem including the occurrence of capacity dropout at a low temperature, thus determining the
constant.
Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric
transient.
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can
break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any
special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety
measures including the use of fuses, etc.
The reverse connection of power supply connector can break down ICs. Take protective measures against the breakdown
due to the reverse connection, such as mounting an external diode between the power supply and the IC’s power supply
terminal.
Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines. In this regard,
for the digital block power supply and the analog block power supply, even though these power supplies has the same
level of potential, separate the power supply pattern for the digital block from that for the analog block, thus suppressing
the diffraction of digital noises to the analog block power supply resulting from impedance common to the wiring patterns.
For the GND line, give consideration to design the patterns in a similar manner.
In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can
break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between
the terminal and the power supply or the GND terminal, the ICs can break down.
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state.
Be noted that using ICs in the strong electromagnetic field can malfunction them.
On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress.
Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set
PCB to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to the
jig. After the completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In
addition, for protection against static electricity, establish a ground for the assembly process and pay thorough attention
to the transportation and the storage of the set PCB.
In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the
parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the
input terminal. Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input terminals
a voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage
to the input terminals when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is
applied, apply to the input terminals a voltage lower than the power supply voltage or within the guaranteed value of
electrical characteristics.
14/16