IM-T-9A BANNER ENGINEERING, IM-T-9A Datasheet - Page 10

• Manufacturer Part Number: IM-T-9A
• Description: Interfacing Module
• Manufacturer: BANNER ENGINEERING

Specifications of IM-T-9A

• Supply Voltage Max: 24VDC
• Control Output Type: 3NO

10
Input Voltage and Current
Supply Protection Circuitry
Overvoltage Category
Pollution Degree
Output Configuration
Output Response Time
Status Indicators
Construction
Mounting
Vibration Resistance
Operating Conditions
Dimensions
Design Standards
Application Notes
Certifications
P/N 62822 rev. C
Output relay contact voltage of 1V to 150V ac/dc: Category III
Output relay contact voltage of 151V to 250V ac/dc: Category II (Category III, if appropriate overvoltage
reduction is provided, as described on page 9.)
2
See Figure 10.
24V dc, +/-15% no polarity, 10% maximum ripple; 50 mA per input channel (approximately 2.4 W)
Protected against transient voltages.
IM-T-9A: 3 normally open output channels
IM-T-11A: 2 normally open output channels and 1 normally closed auxiliary output channel.
Each normally open output channel is a series connection of contacts from two forced-guided (mechanically linked)
relays, K1-K2. The normally closed contact 31-32 is a parallel connection of contacts from K1-K2.
Contacts: AgNi, 5 µm gold-plated
Low Current Rating: The 5 µm gold-plated contacts allow the switching of low current/low voltage. In these low-
power applications, multiple contacts can also be switched in series (e.g., “dry switching”). To preserve the gold
plating on the contacts, do not exceed the following max. values at any time:
High Current Rating: If higher loads must be switched through one or more of the contacts, the minimum and
maximum values of the contact(s) changes to:
Feedback contact rating (Y1-Y2, Y3-Y4):
Mechanical life: 20,000,000 operations
Electrical life: 150,000 cycles @ 1,500 VA; 1,000,000 cycles@ 450 VA; 2,000,000 cycles @ 250 VA; 5,000,000
cycles @ 125 VA
Note: Transient suppression is recommended when switching inductive loads. Install suppressors across
20 milliseconds maximum
2 green LED indicators: K1 energized, K2 energized
Polycarbonate housing rated NEMA 1, IEC IP20
Mounts to standard 35 mm DIN-rail track. Interface Module must be installed inside an enclosure rated NEMA 3
(IEC IP54), or better.
10 to 55Hz @ 0.35 mm displacement per IEC 60068-2-6
Temperature: 0° to +50°C (+32° to 122°F)
Max. Relative Humidity: 90% @ 50°C (non-condensing)
EN 60204-1, IEC 61810-1, EN 60255-1, EN 50205
There are no adjustments and no user-serviceable parts. See page 10 for information regarding repair service.
Min. voltage: 1V ac/dc
Min. current: 5 mA ac/dc
Min. power: 5 mW (5 mVA)
Minimum:
Voltage: 15V ac/dc
Current: 30 mA ac/dc
Power: 0.45 W (0.45 VA)
Min. voltage: 1V ac/dc
Min. current: 5 mA ac/dc
Min. power: 5 mW (5 mVA)
load. Never install suppressors across output contacts (see Warning, page 5).
– Interface Modules
– Interface Modules
Specifications
Max. voltage: 60V
Max. current: 300 mA
Max. power: 7 W (7 VA)
Maximim:
250V ac / 24V dc, 6A resistive
Max. power 150 W (1,500 VA)
IEC 60947-5-1:
AC-15: 230V ac, 3A: DC-13: 24V dc, 4A
Max. voltage: 60V
Max. current: 300 mA
Max. power: 7 W (7 VA)
Banner Engineering Corp.
Banner Engineering Corp.
www.bannerengineering.com • Tel: [phone]
www.bannerengineering.com • Tel: [phone]
•
•
Minneapolis, MN U.S.A.
Minneapolis, MN U.S.A.