QS30ELVC BANNER ENGINEERING, QS30ELVC Datasheet
QS30ELVC
Specifications of QS30ELVC
Related parts for QS30ELVC
QS30ELVC Summary of contents
Page 1
... For 150 mm (6") pigtail with a 5-pin Euro-style connector, add suffix “Q5” to the model number (e.g., QS30ELVCQ5). For 150 mm (6") PUR cable with 5-pin threaded Euro-Style QD, add suffix “QPMA” to the model number (e.g. QS30ELVCQPMA). A model with a QD connector requires a mating cordset (see page 9). ...
Page 2
... A wide assortment of mounting brackets are also available for applications requiring adjustability or robust mechanical protection. The QS30ELVC is configured for operation using the Light SET procedure described on page 4. The sensor is simply aligned to the included retroreflective target and the Light SET is initiated either via the push button or the remote wire input. A reliable detection is assured when the appropriate threshold for clear, translucent or dark object is selected ...
Page 3
... Reflective Object Detection 1. Mount the retroreflector. 2. Align the sensor to the retroreflector. 3. Perform Light SET (page 4) with no object present sing Switchpoint Adjustment (page 6), select clear or medium switchpoint percentage (8% or 16% below the signal from the retroreflector). This will reduce the chance of specular reflection affecting the sensor. QS30ELVC Series ® 3 P/N 139760 rev. A ...
Page 4
... WORLD-BEAM QS30ELVC Series ® Single-Point Light SET • U seful for clear object detection and other applications with small variations in contrast. • S ets a switchpoint at 8 (clear), 16 (medium (dark) percent below the signal from the retroreflector. • S witchpoint position is selectable using the “+” and “-” buttons. Select 8, 16 percent (Switchpoint Selection). • S ensor must be aimed at the reflector during the SET process. All conditions darker than the switchpoint condition result in ON output (Dark Operate). Output ON and OFF conditions can be reversed by changing Light/Dark Operate in SETUP mode (factory setting: Dark Operate) ...
Page 5
... Auto Compensation ON/LO Auto Compensation OFF/LO Auto Compensation OFF/DO * Factory default setting Green Power LED Amber Output LED: Remains active Bargraph: Indicates current setup • S ensor returns to RUN mode with new settings QS30ELVC Series ® Result Setting Combination Auto LED LO LED ON ON OFF OFF P/N 139760 rev ...
Page 6
... Connect the gray wire of the sensor as described on page 2, and four- pulse to either enable or disable the push buttons: The QS30ELVC Alarm State indicates that the sensor requires attention. In all situations, the alarm can be cleared by realigning the sensor to the retroreflector, cleaning the sensor or retroreflector of contamination, and performing a Light SET to establish a valid light signal. ...
Page 7
... Hold Advanced Sensor Power LED OFF Configuration Menu Auto LED Flashing Hold Flash Power: Push button enable /disable 1x for enabled , Repeat twice (legacy method ) 2x for disabled, Repeat twice Restore factory defaults All LEDs off for 1 s QS30ELVC Series ® Exit ...
Page 8
... WORLD-BEAM QS30ELVC Series ® Sensing Beam 660 nm visible red LED Sensing Range and Use 100 (3.9" to 78"); Light SET for clear object detection Supply Voltage 10 to 30V dc (10% max. ripple max current, exclusive of load Supply Protection Circuitry Protected against reverse polarity, over voltage, and transient voltages Delay at Power-Up 250 ms ...
Page 9
... Quick-Disconnect Cables Length Dimensions 2 m (6.5 (15 (30 max. (1.7" max. (1.5" (6.5 (15 (30') M12 x 1 ø (0.6") QS30ELVC Series ® Receiver 12.5 mm 17.6 mm (0.49") (0.69") 33.0 mm (1.30") Emitter 28.8 mm M30 x 1.5 Thread (1.13") max. torque 6 Nm (53 in lbs) with included 30 mm ...
Page 10
... WORLD-BEAM QS30ELVC Series ® NOTE: Other sensor models shown on some views below. SMBQS30L • R ight-angle bracket for cabled sensors • 1 4-gauge stainless steel • ± 12° tilt adjustment • C learance for M4 (#8) hardware 20° R35.0 mm 44.0 mm ø4.3 mm 4.5 mm 11.0 mm 24.0 mm 22.0 mm 64.4 mm R33.0 mm 24° 1.9 mm SMBQS30Y • H eavy-duty die-cast bracket with M18 vertical mounting option • ± 8° tilt adjustment for cabled sensors • ...
Page 11
... Retroreflective Targets • C orner-cube reflector BRT- • 1.2 reflectivity factor* 40X19A • M ax. temp. +50° C (+122° F) • Supplied with sensor 19 50.0 mm 60.2 mm 3.5 mm ø4.0 mm QS30ELVC Series ® • C orner-cube reflector BRT- • 3.0 reflectivity factor* 92X92C • Max. temp. +50° C (+122° F) • Optional 100 mm 7 100 mm Clear ...
Page 12
... WORLD-BEAM QS30ELVC Series ® WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products ...