QS30LDLQ BANNER ENGINEERING, QS30LDLQ Datasheet

Page 1

... QS30LDLQ *9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., QS30LD W/30). A model with a QD connector requires a mating cable (see page 10). WARNING . . . Not To Be Used for Personnel Protection ! Never use this product as a sensing device for personnel protection. Doing so could lead to serious injury or death. ...

Page 2

... Programming Green Power ON Indicator Bargraph Display Switching Threshold SETUP Status Indicators: Delay Dark Operate Light Operate Figure 1. QS30 features Banner Engineering Corp. Banner Engineering Corp. Minneapolis, MN U.S.A. Minneapolis, MN U.S.A. • • www.bannerengineering.com • Tel: 763.544.3164 www.bannerengineering.com • Tel: 763.544.3164 Push Buttons ...

Page 3

... Do not permit a person to stare at the laser from within the beam. • Do not point the laser at a person’s eye at close range. • Terminate the beam emitted by a Class 2 laser product at the end of its useful path. Banner Engineering Corp. Minneapolis, MN U.S.A. • ...

Page 4

... In SETUP mode, press and hold both the Static (-) and Dynamic (+) buttons (or hold the remote line) for 2 seconds to exit. The sensor returns to RUN mode and saves the current setting. 4 P/N 109027 rev. C Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...

Page 5

... Present Output • Present Output OFF OFF condition condition • Click • Single-pulse remote line Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 QS30 Series Diffuse-Mode Laser Sensor Two-Point Static TEACH • Two-point TEACH • Sets a single switching threshold • ...

Page 6

... Sensor returns to RUN mode with new settings Teach Unacceptable Power LED: OFF Bargraph: # flash to show fail Sensor returns to RUN mode without changing settings Banner Engineering Corp. www.bannerengineering.com • Tel: 763.544.3164 Darkest Taught Lightest Taught Condition Condition Sensor positions threshold midway ...

Page 7

... Present Output ON • Double-pulse condition remote line • Double-click T Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 QS30 Series Diffuse-Mode Laser Sensor Single-Point Static TEACH (Sensing Window) • Sets a single ON condition • All other conditions (lighter or darker) result in OFF output • ...

Page 8

... Connect the gray wire of the sensor as described on page 4, and four-pulse to either enable or disable the push buttons P/N 109027 rev SETUP { Status Indicators Figure 5. SETUP mode Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Press and hold both push buttons to access SETUP mode ...

Page 9

... Cabled Models 30V dc bu – wh 150 mA max. load Load bk Load gy Remote Teach Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 QS30 Series Diffuse-Mode Laser Sensor Dimensions QD Models 35.0 mm (1.38") 22.0 mm 3.5 mm (0.87") (0.14") CLASS 1 LASER PRODUCT Complies with 21 CFR 1040.10 and 1040 ...

Page 10

... Quick-Disconnect Cables Length Dimensions 44 mm max. (1.7" max. (1.5") M12 x 1 ø (0.6") Pin-out ø (0.6") M12 x 1 Brown Wire Black Wire 38 mm max. (1.5") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 White Wire Blue Wire Gray Wire ...

Page 11

... X Ø 3.3 mm (0.28") (0.13" (1.30") (2.20") 18.0 mm (0.71") 16.35 mm (0.64") 24.0 mm (0.94") 35.0 mm (1.38") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 QS30 Series Diffuse-Mode Laser Sensor Brackets SMBQS30LT 4.5mm [0.18"] 24.0mm [0.95"] 33.0mm [1.3"] 59.4mm [2.4"] 24° ...

Page 12

... This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. P/N 109027 rev.C Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com ...