ATC18002 PANASONIC EW, ATC18002 Datasheet - Page 9

• Manufacturer Part Number: ATC18002
• Description: PMH(48M.M.) RUBBER GASKET
• Manufacturer: PANASONIC EW

type), W through P (11-pin type) or
and
the power supply wire is wired parallel to
the high voltage wire or power wire, an
induced voltage may be generated
between the power supply terminals.)
4) Have the power supply voltage pass
through a switch or relay so that it is
applied at one time. If the power supply
is applied gradually, the counting may
malfunction regardless of the settings,
the power supply reset may not function,
or other such unpredictable occurrence
may result.
2. Input connections
The power circuit has no transformer.
When an input signal is fed to two or
more counters at once, do not arrange
the power circuit in an independent way.
If the counter is powered on and off inde-
pendently as shown in Fig. A, the coun-
ter's internal circuitry may get
damaged.Be careful never to allow such cir-
cuitry. (Figs. A, B and C show the circuitry for
the 11-pin type.)
LC4H series CAUTIONS FOR USE
PRECAUTIONS DURING USAGE
1. Terminal wiring
1) When wiring the terminals, refer to the
terminal layout and wiring diagrams and
be sure to perform the wiring properly
without errors.
2) For embedded installation applica-
tions, the screw-down terminal type is
recommended.
Use either the rear terminal block (AT8-
RR) or the 8P cap (AD8-RC) for the 8-
pin type, and the 11P cap (AT8-DP11)
for the 11-pin type. Avoid soldering
directly to the round pins on the unit.
For front panel installation applications,
use the 11-pin type DIN rail terminal
block (ATC18004).
3) After turning the unit off, make sure
that any resulting induced voltage or
residual voltage is not applied to power
supply terminals W through U (8-pin
( Fig. A )
Input contact
point or transistor
If independent power circuitry must be used,
keep the input contacts or transistors sepa-
rate from each other, as shown in Fig. B.
When power circuitry is not independent,
98
2
(screw-down terminal type). (If
3
3
2
2
Input
terminal
Input
terminal
10
10
Power
supply
1
Input contact
point or transistor
one input signal can be fed to two or
more counters at once, as shown in Fig. C.
3. Input and output
1) Signal input type
(1) Contact point input
Use highly reliable metal plated contacts.
Since the contact point’s bounce time
leads directly to error in the count value,
use contacts with as short a bounce time
as possible. In general, select Input 1
and Input 2 to have a maximum counting
speed of 30 Hz and to be reset with a
minimum input signal width of 20 ms.
(2) Non-contact point input
Note: The LC4H-W does not have the lock input
R
Connect with an open collector. Use
transistors whose characteristics satisfy
the criteria given below.
V
I
I
Also, use transistors with a residual volt-
( Fig. B )
Input contact
point or transistor
( Fig. C )
Input contact
point or transistor
C
CBO
CEO
7
= 20 mA min.
8-pin type
11-pin type
Screw terminal type
.
= 6µA max.
= 20 V min.
Reset input
3
3
3
3
Input 1
2
2
2
2
Input
terminal
Input
terminal
Input
terminal
Input
terminal
Input 2
10
10
10
10
02/2003
1
3
6
Lock
input
—
4
7
5
5
8
4
6
9
Power
supply
Power
supply
10
3
7
age of less than 2 V when the transistor
is on.
* The short-circuit impedance should be
Note: The LC4H-W does not have the lock input
R
less than 1 kΩ.
[When the impedance is 0 W, the current
coming from the input 1 and input 2 ter-
minals is approximately 12 mA, and from
the reset input and lock input terminals is
approximately 1.5 mA.]
Also, the open-circuit impedance should
be more than 100 kΩ.
* As shown in the diagram below, from a
2) The input mode and output mode
change depending on the DIP switch set-
tings. Therefore, before making any con-
nections, be sure to confirm the opera-
tion mode and operation conditions cur-
rently set.
3) For the power supply of the input
non-contact point circuit (proximity
switches, photoelectric switches, etc.)
with a power supply voltage of between
12 and 40 V, the signal can be input
without using an open collector transis-
tor. In the case of the diagram below,
when the non-contact point transistor Q
switches from off to on (when the signal
voltage goes from high to low), the sig-
nal is input.
8-pin type
11-pin type
Screw terminal type
7
8-pin type
11-pin type
Screw terminal type
.
(The above example is for reset input)
12 to 40V DC
Reset input
Q
Input 1
Reset input
Input 2
1
3
6
1
3
6
Lock
input
—
4
7
—
4
7
5
5
8
5
5
8
4
6
9
4
6
9
10
3
7
10
3
7