CUB5VB00 Red Lion Controls, CUB5VB00 Datasheet - Page 10

• Manufacturer Part Number: CUB5VB00
• Description: Voltage Meter
• Manufacturer: Red Lion Controls
• Type: Voltager

Specifications of CUB5VB00

• No. Of Digits / Alpha: 5
• Meter Function: DC Voltmeter
• Meter Range: 0mV To 200mV / 0V To 2V / 0V To 20V / 0V To 200V
• Digit Height: 12.2mm
• Operating Temperature Range: -35°C To +75°C
• Meter Signal Input: Voltage
• Accuracy: ±0.1% %
• Connection Type: Screw
• Cut Out, Panel: 2.68×1.3 "
• Dimensions: 2.95"L×1.86"W×1.54"H
• Display Digit Height: 0.48 "
• Display Type: LCD
• Function: Voltage
• Material, Casing: Plastic
• Number Of Digits: 5
• Primary Type: Electronic
• Range, Measurement: 200 mVDC to 200 VDC
• Special Features: Communication and Control
• Voltage, Supply: 9 to 28 VDC
• Power Supply: 9 to 28 VDC
• Dc Current: 200 μA to 200 mA
• Dc Voltage: 200 mV to 200 V
• Process Signals: 0(4) to 20 mA or 0 - 10 VDC
• Display Mode: Selectable Transmissive
• Rohs Compliant: Yes
• Backlighting Color: Red Or Green
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

SP - Hys



Act-n
SP + ½Hys
SP - ½Hys
module is installed in the meter.
SPSEL
Enb-2
6.4 MODULE 4 - S
High Acting (Unbalanced Hys) =
Enter the setpoint (output) to be programmed. The
parameters will reflect the chosen setpoint number. After the chosen setpoint
is completely programmed, the display will return to
each setpoint to be programmed. Select
setpoints available is setpoint output card dependent.
Select
selected, the unit returns to
Enter the action for the selected setpoint (output). See Setpoint Output
Figures for a visual detail of each action.
OUTPUT
OUTPUT
The Setpoint Output Parameters are only active when an optional output
High Acting (Balanced Hys) =
STATE
SEL
STATE
SP
4-SPt
SPSEL
SP
Setpoint
Select
HI-Ub
YES
OFF
OFF



to enable Setpoint 2 and access the setup parameters. If
NO
NO
HI-bL
LO-bL
HI-Ub
LO-Ub
TRIGGER POINTS
TRIGGER POINTS
Act-n
Setpoint
Action
YES
=
=
=
=
ON
ON
HI-bL
SETPOINT 2 ENABLE
SETPOINT SELECT
SETPOINT ACTION
High Acting, with balanced hysteresis
Low Acting, with balanced hysteresis
High Acting, with unbalanced hysteresis
Low Acting, with unbalanced hysteresis
SPSEL
OFF
HI-bL
OFF
HI-Ub
NO
NO
SPt-n
and setpoint 2 is disabled.
LO-bL
Setpoint
Value
Hys
Hys
SP + ½Hys
SP - ½Hys
SP + Hys
NO
Low Acting (Unbalanced Hys) =
OUTPUT
OUTPUT
STATE
SP
Low Acting (Balanced Hys) =
SP-1
STATE
to exit the module. The number of
SP
HI-Ub
HYS-n
Hysteresis
Value
OFF
OFF
ETPOINT
SP-2
SPSEL
n
TRIGGER POINTS
TRIGGER POINTS
LO-Ub
. Repeat steps for
in the following
ON
ON
PARAMETER MENU
tON-n
On Time
Delay
LO-bL
OFF
OFF
LO-Ub
O
NO
is
UTPUT
Hys
Hys
tOF-n
10
Off Time
Delay
LAtCH

and hysteresis values follow the selection set in Module 1.

explanation of how setpoint output actions (balanced and unbalanced) are
affected by the hysteresis. When the setpoint is a control output, usually
balanced hysteresis is used. For alarm applications, usually unbalanced
hysteresis is used. For unbalanced hysteresis modes, the hysteresis functions on
the low side for high acting setpoints and functions on the high side for low
acting setpoints.
Note: Hysteresis eliminates output chatter at the switch point, while time delay

after the trigger point is reached. A value of 0.0 allows the meter to update the
output status per the response time listed in the Specifications.

after the trigger point is reached. A value of 0.0 allows the meter to update the
output status per the response time listed in the Specifications.

HYS-n
tON-n
tOF-n
rSt-n
SPt-n
automatically reset off at the trigger points per the Setpoint Action shown in
Setpoint Output Figures. The “on” output may be manually reset (off)
immediately by the front panel
off until the trigger point is crossed again.
the trigger point per the Setpoint Action shown in Setpoint Output Figures.
Latch means that the output can only be turned off by the front panel
Enter the desired setpoint value. The decimal point position for the setpoint
Enter desired hysteresis value. See Setpoint Output Figures for visual
can be used to prevent false triggering during process transient events.
Enter the time value in seconds that the output is delayed from turning on
Enter the time value in seconds that the output is delayed from turning off
= Latch with immediate reset action; This action latches the output on at
P
10000
Output Reset
rSt-n
Auto
Action
ARAMETERS



0. 0

0. 0

2
Auto
Enter the reset action of the output. See figure for details.
OUTPUT RESET ACTION
= Automatic action; This action allows the output to
Output Reset
rEn-n
W/Display
HYSTERESIS VALUE
Reset
SETPOINT VALUE
OFF TIME DELAY
Auto
0. 0
0. 0
ON TIME DELAY
-19999
to
to
1
RST
to
599. 9
599. 9
59999
to
button or user input.The output remains
Stb-n
(
Operation
Standby
seconds
seconds
4-SPt
99999
LAtCH
)
Change Display
Output State
Unit Only
Backlight
ChC-n
Color with
L-dLY
Pro
RST