K33L1A Omron, K33L1A Datasheet - Page 6

• Manufacturer Part Number: K33L1A
• Description: OPTION BOARD, SENSOR, PS+4-20MA
• Manufacturer: Omron

Specifications of K33L1A

• Accessory Type: Sensor Power Supply / Output Board
• Voltage Rating: 12VDC
• Current Rating: 80mA
• Svhc: No SVHC (15-Dec-2010)
• For Use With: K3HB-R Rotary Pulse Indicator, K3HB-P Timer Interval Indicator
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

■ Characteristics
6
Display range
Measurement accuracy
Measurement range
Input signals
Connectable sensors
Comparative output response
time (transistor output)
Linear output response time
Insulation resistance
Dielectric strength
Noise immunity
Vibration resistance
Shock resistance
Weight
Degree of
protection
Memory protection
Applicable standards
EMC
(at 23±5 C)
Rotary Pulse Indicator
Front panel Conforms to NEMA 4X for indoor use (equivalent to IP66)
Rear case
Terminals
Functions F1, F6: ±0.006% rgd ±1 digit (for voltage pulse/open collector sensors)
Functions F2 to F5: ±0.02% rgd ±1 digit (for voltage pulse/open collector sensors)
Functions F1 to F6: 0.5 mHz to 50 kHz (for voltage pulse/open collector sensors)
No-voltage contact (30-Hz max. with ON/OFF pulse width of 15 ms min.)
Voltage pulse (50-KHz max. with ON/OFF pulse width of 9 µs min.; ON voltage: 4.5 to 30 V;
OFF voltage: 30 to 2 V; input impedance: 10 k )
Open collector (50-KHz max. with ON/OFF pulse width of 9 µs min.)
ON residual voltage: 3 V max.
OFF leakage current: 1.5 mA max.
Load current:
Functions F1 to F6: 100 ms max. (time until the comparative output is made when there is a forced sudden
change in the input signal from 15% to 95% or 95% to 15%.)
Functions F1 to F6: 110 ms max. (time until the final analog output value is reached when there is a forced
sudden change in the input signal from 15% to 95% or 95% to 15%.)
20 M min. (at 500 VDC)
2,300 VAC for 1 min between external terminals and case
100 to 240 VAC models:
24 VAC/VDC models:
Frequency: 10 to 55 Hz; Acceleration: 50 m/s
150 m/s
Approx. 300 g (Base Unit only)
IP20
IP00 + finger protection (VDE0106/100)
EEPROM (non-volatile memory)
Number of rewrites: 100,000
UL61010C-1, CSA C22.2 No. 1010.1 (evaluated by UL)
EN61010-1 (IEC61010-1): Pollution degree 2/Overvoltage category II
EN61326: 1997, A1: 1998, A2: 2001
EMI: EN61326+A1 industrial applications
Electromagnetic radiation interference
Terminal interference voltage
EMS: EN61326+A1 industrial applications
Electrostatic Discharge Immunity
Radiated Electromagnetic Field Immunity
Electrical Fast Transient/Burst Immunity
Surge Immunity
Conducted Disturbance Immunity
Power Frequency Magnetic Immunity
Voltage Dips and Interruptions Immunity
19,999 to 99,999
(waveform with 1-ns rising edge and pulse width of 1 s/100 ns)
(waveform with 1-ns rising edge and pulse width of 1 s/100 ns)
CISPR 11 Group 1, Class A: CISPRL16-1/-2
CISPR 11 Group 1, Class A: CISPRL16-1/-2
EN61000-4-2: 4 kV (contact), 8 kV (in air)
EN61000-4-3: 10 V/m 1 kHz sine wave amplitude modulation (80 MHz to 1 GHz, 1.4 to 2 GHz)
EN61000-4-4: 2 kV (power line), 1 kV (I/O signal line)
EN61000-4-5: 1 kV with line (power line), 2 kV with ground (power line)
EN61000-4-6: 3 V (0.15 to 80 MHz)
EN61000-4-8: 30 A/m (50 Hz) continuous time
EN61000-4-11: 0.5 cycle, 0 /180 100% (rated voltage)
1,500 V at power supply terminals in normal or common mode
1,500 V at power supply terminals in normal or common mode
K3HB-R
2
(100 m/s
2
for relay outputs) 3 times each in 3 axes, 6 directions
Must be able to properly switch load currents of 5 mA or less.
Must have a switching capacity of 20 mA or higher.
2
, 10 sweeps of 5 min each in X, Y, and Z directions