IFMR0036 Red Lion Controls, IFMR0036 Datasheet - Page 8

• Manufacturer Part Number: IFMR0036
• Description: Isolation Amplifier
• Manufacturer: Red Lion Controls
• Type: Speedr

Specifications of IFMR0036

• Width: 3.12"
• Signal Input Type: Selectable Current Or Voltage
• Configuration Setup: DIP Switch
• Supply Voltage Max: 32VDC
• Iso-amp Mounting Type: DIN Rail
• Display Alarm Type: Relay
• Input Accuracy: ± 0.1% Of FS
• Application: The IFMR utilizes a seven position DIP switch, a rotary switch, a pushbutton and two indication LEDs to accomplish input circuit configuration, operational parameter set-up, input signal, and relay status indication
• Brand/series: IFMR Series
• Contact Form: SPDT
• Current Rating: 5 A
• Dimensions: 27.5mmW×4.2mmH×79.2mmD
• Display Type: LED
• Input Type: Analog
• Mounting Type: DIN Rail
• Output Type: Relay
• Power, Rating: 2 W
• Primary Type: Controller
• Sensor, Input: 12 VDC
• Standards: cURus, CE
• Temperature, Operating: 0 to +50 °C
• Termination: Screw
• Voltage, Rating: 9 to 32 VDC
• Voltage, Supply: 9-32 VDC
• Signal Output Type: Current
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: Sensors/Switches/TTL

Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel [phone]
Fax [phone]
TROUBLESHOOTING
company numbers listed.
INSTALLATION
standard DIN style mounting rails, including G profile rail according to
EN50035 - G32 , and top hat (T) profile rail according to EN50022 - 35 x
7.5 and 35 x 15. The unit should be installed in a location that does not
exceed the maximum operating temperature and provides good air
circulation. Placing the unit near devices that generate excessive heat
should be avoided.
G Rail Installation
style DIN rail, angle the module
so that the upper groove of the
“foot” catches under the lip of the
top rail. Push the module toward
the rail until it snaps into place. To
remove a module from the rail,
push up on the bottom of the
module while pulling out away
from the rail.
For further technical assistance, contact technical support at the appropriate
The unit is equipped with a universal mounting foot for attachment to
To install the IFMR on a “G”
NL - 3821 AD Amersfoort
Fax [phone]
Tel [phone]
Red Lion Controls
T Rail Installation
“T” style rail, angle the
module so that the top groove
of the “foot” is located over
the lip of the top rail. Push the
module toward the rail until it
snaps into place. To remove a
module from the rail, insert a
screwdriver into the slot on the
bottom of the “foot”, and pry
upwards on the module until it
releases from the rail.
Printerweg 10
To install the IFMR on a
Europe
Ahmedabad-382480 Gujarat, India
APPLICATION 1
sensing the speed of a 60 tooth gear attached to a shaft. The shaft speed
should not exceed 2000 RPM.
an overspeed condition is detected, and to turn off the alarm when the speed
returns to normal. The Mode of Operation is set for Mode #1 (overspeed
trip, automatic release upon return to normal).
described in Section 2.0 or determine the Trip Frequency using the
following formula:
set at 0.25%; activation of the relay occurs at 2000 Hz, and release occurs
at 1995 Hz.
APPLICATION 2
system drops below setpoint.
a key way on the shaft of a motor. The motor is turning at 1750 RPM. When
the speed of the motor drops below 1250 RPM, the IFMR latches the output
until the user resets the output with an external push button.
trip, release only after Alarm Reset pulled to common). Determine the Trip
Frequency using the following formula:
Fax [phone]
GST Road, New Ranip,
Tel [phone]
54, Vishvas Tenement
An APLR is connected to an LMPC (logic magnetic pickup) that is
The IFMR is placed in parallel with the APLR to activate an alarm when
To set the value of the alarm, either apply the maximum input signal as
Set the Trip Frequency with the rotary switch for 2000 Hz.
With Trip point Offset set at 0.00% (No Offset) and Trip Point Hysteresis
The IFMR can be used in a speed monitoring system to detect when the
The IFMR is wired to a PSAC (inductive proximity sensor) that is sensing
The mode of operation of the IFMR is set for 5 (UNDERSPEED Latched
Set the Trip Frequency with the rotary switch for 20.83 Hz.
Red Lion Controls
LMPC
India
Trip Freq. = 1250 RPM x 1 PPR = 20.83 Hz.
Trip Freq. = 2000 RPM x 60 PPR = 2000 Hz
Trip Freq. = units/measure x pulses/unit
Trip Freq. = RPM x PPR
60 sec.
APLR
IFMR
7
8
9
7
8
9
seconds/measure
+12V
COMM.
INPUT
+12V
INPUT
COMM.
60 sec
60
Building 13, No.99 Tianzhou Road
ON 1 2 3
ShangHai, P.R. China 200223
Fax [phone]
Tel [phone]
Unit 101, XinAn Plaza
Red Lion Controls
China