AD9276-80KITZ Analog Devices Inc, AD9276-80KITZ Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9276-80KITZ
Manufacturer Part Number
AD9276-80KITZ
Description
80MSPS ADC Converter Evaluation Board
Manufacturer
Analog Devices Inc
Datasheet
1.AD9276BSVZ.pdf
(48 pages)
Specifications of AD9276-80KITZ
Silicon Manufacturer
Analog Devices
Application Sub Type
ADC
Kit Application Type
Data Converter
Silicon Core Number
AD9276
Number Of Adc's
1
Number Of Bits
12
Sampling Rate (per Second)
80M
Data Interface
Serial, SPI™
Inputs Per Adc
1 Differential
Input Range
*
Power (typ) @ Conditions
195mW @ 40MSPS
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD9276
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD9276
Parameter
POWER SUPPLY
ADC RESOLUTION
ADC REFERENCE
1
2
See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions and information about how these tests were
completed.
The overrange condition is specified as being 6 dB more than the full-scale input range.
Input-Referred Noise Voltage
Noise Figure
Input-Referred Dynamic Range
Output-Referred SNR
Two-Tone Intermodulation (IMD3)
Quadrature Phase Error
I/Q Amplitude Imbalance
Channel-to-Channel Matching
Mode I/Mode II/Mode III
AVDD1
AVDD2
DRVDD
I
I
I
Total Power Dissipation
Power-Down Dissipation
Standby Power Dissipation
Power Supply Rejection Ratio
Output Voltage Error
Load Regulation at 1.0 mA
Input Resistance
AVDD1
AVDD2
DRVDD
(Including Output Drivers)
(PSRR)
1
Test Conditions/Comments
R
LNA gain = 15.6 dB
LNA gain = 17.9 dB
LNA gain = 21.3 dB
R
LNA gain = 15.6 dB
LNA gain = 17.9 dB
LNA gain = 21.3 dB
R
LNA gain = 15.6 dB
LNA gain = 17.9 dB
LNA gain = 21.3 dB
−3 dBFS input, f
1 kHz offset
f
I to Q, all phases, 1 σ
I to Q, all phases, 1 σ
Amplitude I to I, Q to Q, 1 σ
TGC mode
CW Doppler mode
TGC mode, no signal
CW Doppler mode per channel enabled,
no signal
TGC mode, no signal
CW Doppler mode with eight channels
enabled, no signal
VREF = 1 V
VREF = 1 V
f
IMD3 relative to A
Phase I to I, Q to Q, 1 σ
RF1
4LO
S
S
S
= 0 Ω, R
= 50 Ω, R
= 0 Ω, R
= 5.015 MHz, f
= 20 MHz, A
FB
FB
FB
= ∞
= ∞
= ∞
RF1
RF
RF2
= 2.5 MHz, f
RF2
= 0 dB, A
= 5.020 MHz,
Rev. 0 | Page 6 of 48
RF2
4LO
= −20 dB,
= 10 MHz,
1.7
Min
1.7
2.7
Typ
1.5
1.4
1.3
5.7
5.3
4.8
164
162
160
155
−58
0.15
0.015
0.5
0.25
1.8
3.0
1.8
190/263/317
15
365
30
49/51/52
1560/1690/
1780
750
1.6
12
2
6
175/200/210
Max
1.9
3.6
1.9
1800/1940/
2050
5
±20
Unit
nV/√Hz
nV/√Hz
nV/√Hz
dB
dB
dB
dBFS/√Hz
dBFS/√Hz
dBFS/√Hz
dBc/√Hz
dB
Degrees
dB
Degrees
dB
V
V
V
mA
mA
mA
mA
mA
mW
mW
mW
mW
mV/V
Bits
mV
mV
kΩ