HFBR-0534 Avago Technologies US Inc., HFBR-0534 Datasheet

HFBR-0534

Manufacturer Part Number

HFBR-0534

Description

Fiber Optic Evaluation Kit

Manufacturer

Avago Technologies US Inc.

Datasheet

1.HFBR-0534.pdf (3 pages)

Specifications of HFBR-0534

Silicon Manufacturer

Avago

Kit Contents

Fully Assembled Evaluation Board, CD-ROM Containing Software, 9-Pin Serial Cable

Main Purpose

Interface, Transceiver

Embedded

Utilized Ic / Part

SFP Modules with DMI

Primary Attributes

Two-wire Serial Interface for DMI

Secondary Attributes

GUI, LED Indicators

Operating Voltage

9 V to 12 V

Description/function

Fiber Optic Kit

Maximum Operating Temperature

+ 50 C

Minimum Operating Temperature

0 C

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Lead Free Status / RoHS Status

Lead free / RoHS Compliant, Contains lead / RoHS non-compliant

Current page: 1 of 3
Download datasheet (188Kb)

HFBR-0534 Evaluation Kit

for Diagnostic Monitoring Interface (DMI)

Small Form Pluggable (SFP) Transceivers

Product Brief

Description

For bench top evaluation, the HFBR-0534 is the

recommended tool for Avago Technologies new Small-

Form-Pluggable (SFP) transceivers with the Diagnostic

Monitoring Interface (DMI). The HFBR-0534 includes

the necessary two-wire serial interface to communicate

with the Diagnostic Monitoring Interface and provides a

standard 9 pin serial interface to connect to a PC.

A Window’s based Graphical User Interface (GUI) provides

the user an easy, straightforward way to communicate to

SFP transceivers. The interface software is customized

to allow quick verification of the feature sets defined in

the SFF-8472 MSA. The HFBR-0534 requires only one

input DC supply voltage (9 V to 12 V) to power all board

components, including the micro-controller, and both the

receiver and transmitter sections of the SFP transceiver.

Just plug in the DMI SFP and your ready to go. Using

Avago Technologies custom PC software (included as part

HFBR-0534 evaluation board kit), the user can then read

specific bytes from the SFP’s memory pages (decoding into

ASCII or HEX), access and log the internal measurements of

the transceiver (temperature, supply voltage, transmitter

bias current, transmitter output power, and received

optical power) as well as program the device EEPROM.

Using a Bit-Error-Ratio Tester (BERT ) and a Digital

Communication Analyzer (DCA), the HFBR-0534 is also

suitable for evaluating the optical characteristics, including

the eye diagram, jitter, and rise/fall time and the electrical

characteristics, including the receiver electrical eye

diagram, jitter, and rise/fall time.

custom PC software (included as part

Features

•

Applications

•

Included in the HFBR-0534 Evaluation Kit:

- An evaluation board

- Software

- 9 pin serial cable

- 110 V/220 V power supply

On board potentiometer to adjust the voltage to the

SFP for 2.64 to 3.65 V

Test points for easy probing of Mod_Def signals, TX_

Fault and LOS signals.

On-board hardware switch for toggling of TX_Disable

control signal

Onboard LEDS to monitor the status of :

- LOS LED - turns on when LOS hard-signal is asserted

by SFP module

- Mod_Def(0) LED – turns on when a module is pres-

ent

- TX_Fault LED – turns on when TX_Fault is asserted

by module

- TX_disable LED – on when TX is enabled, turns off

when TX is disabled

GUI software allows easy decoding of 0xA0 and 0xA2

page byte contents (per SFF-8472 MSA)

GUI sub-window enables quick execution of byte write

operations; delay between write operations is adjust-

able

Supports two-wire serial interface @ 100 kHz

Operating Temperature Range:

0 °C to +50 °C

Bench top evaluation of Avago’s SFP with DMI mod-

ules

Logging and Recording of Monitoring Values

Printable Reports of SFP content and decoded infor-

mation

Reading and writing to on-board SFP memory

Optical / Electrical testing of all Avago SFP modules

Related parts for HFBR-0534

HFBR-0534 Summary of contents

Page 1

... Just plug in the DMI SFP and your ready to go. Using Avago Technologies custom PC software (included as part custom PC software (included as part HFBR-0534 evaluation board kit), the user can then read specific bytes from the SFP’s memory pages (decoding into ASCII or HEX), access and log the internal measurements of ...

Page 2

Additional Equipment Recommended • Fiber optic cables - and 50/125 µm or 62.5/125 µm, 9/125 µ Loopback (<1M and 50/125 µm or 62.5/125 µm, 9/125 µm) • 86100A Agilent Digital Communications ...

Page 3

Block Diagram Note: The electrical loop back and optical loop back cable (shown in this diagram) provides an emulated signal in the absence of a signal generator for basic verifica- tion of RX and TX Monitoring. For product information and ...

Related keywords

HFBR-0534 datasheet
HFBR-0534 data sheet
HFBR-0534 pdf datasheet
HFBR-0534 component
HFBR-0534 part
HFBR-0534 distributor
HFBR-0534 RoHS
HFBR-0534 datasheet download