8080-1G7 Tyco Electronics, 8080-1G7 Datasheet - Page 77

• Manufacturer Part Number: 8080-1G7
• Description: TRANSISTOR SOCKET, 3POS, THROUGH HOLE
• Manufacturer: Tyco Electronics

Specifications of 8080-1G7

• Connector Type: TO-3 Socket
• No. Of Contacts: 3
• Pitch Spacing: 5.46mm
• Contact Termination: Solder
• Contact Material: Beryllium Copper
• Contact Plating: Gold
• Socket Mounting: PC Board
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

FEATURES:
The 8041 Series printed wiring board mounted test jacks require very little
mounting space. Used in many applications as signal test points, they are
also used as electromechanical interfaces from daughter cards to mother
boards. Test jack M8041-15G is qualified to MIL-C-39024/11. This series
test jack accepts .080 (2,03) inch dia. test probes in either side or top side
entry models.
• Low profile for close board-to-board stacking
• Test jack cannot be damaged by using oversized probe
• Probe side entry or top and side entry, both qualified to MIL-C-
• Dimple on printed circuit terminals, retains test jack in P.W.B. during
• Ten brilliant insulation colors available for quick test point reference
• Top entry allows test jack to be probed while being used as an
MATERIAL SPECIFICATIONS:
Insulator............................Nylon
Contacts............................Beryllium copper
Platings ............................Gold
8041 Series
Note: Before ordering, see Cross Reference in Section 15 for
equivalent Tyco Electronics Part Number.
Products for Industrial &
Commercial Applications
39024/11
flow soldering
interconnection socket
8041-1G4-1
Dimensions are shown for
reference purposes only.
Specialty Sockets
Printed Circuit Test Jacks
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
PERFORMANCE SPECIFICATIONS:
MECHANICAL
Vibration ..........................15 G's, 0 - 55 Hz monitored for 10 micro seconds
Mechanical Shock............50 G's, monitored for 10 micro seconds opening
Durability ........................500 Insertions
Insertion Force ................0.080 (2,03) dia. pin., 5.0 lb. max.
Withdrawal Force ............0.080 (2,03) dia. pin., 227 grams (8 oz.) min.
Permeability ....................2.0 Mu max. MIL-I-17214
Solderability ....................Passed MIL-STD-202, Method 208
ELECTRICAL
Bulk Contact
Current Rating..................5 Amps DC
Operating Voltage ..........1,500 Volts RMS @ sea level,
Dielectric Withstanding
Insulation Resistance........5,000 x 10
Capacitance ......................1 pF @ 5 MHZ
ENVIRONMENTAL
Operating Temperature ....-65°C to +125°C
Salt spray..........................4 Milliohms @ 5 Amps per MIL-STD-202,
Humidity ..........................1,000 x 10 6 Ohms per MIL-STD-202, Method 101
Thermal Shock ................-65°C to +125°C per MIL-STD-202, Method 107
NOTE: Military Test Reference applies specifically to MIL-Qualified Components.
..........................................
Resistance ......................4 Milliohms @ 5 Amps, military;
Voltage ..........................2,500 Volts RMS @ sea level, 500 Volts RMS
Specifications subject to
change.
5 Milliohms @ 5 Amps, commercial
350 Volts RMS @ 50,000 feet
opening per MIL-STD-202, Method 201
per MIL-STD-202, Method 202
@ 50,000 feet per MIL-STD-202, Method 301
Method 101
6
Ohms, MIL-C-39024 Section 4.6.5
Technical Support Center
1-800-522-6752
www.tycoelectronics.com
Catalog 1307612
Revised 7-01
5077
5