LQ104S1LG61 Sharp Microelectronics, LQ104S1LG61 Datasheet - Page 17

• Manufacturer Part Number: LQ104S1LG61
• Description: LCD Graphic Display Modules & Accessories 10.4 2 x CCFT SVGA LVDS I/F 450nit
• Manufacturer: Sharp Microelectronics

Specifications of LQ104S1LG61

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.Handling Precautions
l) Connect GND to 4 place of mounting holes to stabilize against EMI and external noise.
m) There are high voltage portions on the backlight. It is very dangerous to touch carelessly.
b) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist.
d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth when handling.
h) Since there is a circuit board in the module back, stress is not added at the time of a design assembly.
k) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD panel is
n) When handling LCD modules and assembling them into cabinets, please be noted that long-term storage
o) Cold cathode fluorescent lamp in LCD panel contains a small amount of mercury, please follow local ordinances
p) Be careful of a back light lead not to pull by force at the time of the wiring to an inverter, or line processing.
q) When install LCD modules in the cabinet, recommended torque value is “0.294 ± 0.02N ･ m (3.0 ± 0.2kgf ･ cm)”.
u) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.
v) If a minute particle enters in the module and adheres to an optical material, it may cause display non-uniformity issue,
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
c) Since the front polarizer is easily damaged, pay attention not to scratch it.
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with care.
i) Protection film is attached to the module surface to prevent it from being scratched .
j) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching
r) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets inside your eye
s) Notice:Never dismantle the module , because it will cause failure.
t) Be careful when using it for long time with fixed pattern display as it may cause afterimage.
Please don ’ t remove the fixed tape, insulating tape etc. that was pasted on the original module.
(except for protection film of the panel and the crepe tape (yellow tape) of fixing lamp cable temporarily.)
(Please use a screen saver etc., in order to avoid an afterimage.)
Be sure to confirm it in the same condition as it is installed in your instrument.
Blow away dust on the polarizer with antistatic Ｎ
It is recommended to peel off softly using the adhesive tape when soil or finger oil is stuck to the polarizer.
When unavoidable, wipe off carefully with a cloth for wiping lenses.
or mouth by mistake.
It may lead to electrical shock. When exchange lamps or getting service, turn off the power without fail.
Observe all other precautionary requirements in handling components.
Please make it like. If stress is added, there is a possibility that circuit parts may be damaged.
Peel the film off slowly , just before the use, with strict attention to electrostatic charges.
Blow off 'dust' on the polarizer by using an ionized nitrogen.
protective board over the LCD, be careful about the optical interface fringe etc. which degrades display quality.
used under such environment.
in the environment of oxidization or deoxidization gas and the use of such materials as reagent,solvent, adhesive,
or regulations for disposal.
If adjusted value is changed, the specification may not be satisfied.
etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan.
resin, etc. which generate these gasses, may cause corrosion and discoloration of the LCD modules.
2
blow. It is undesirable to wipe off because a polarizer is sensitive.
LD19604A-14