LQ121S1DG61 Sharp Microelectronics, LQ121S1DG61 Datasheet - Page 16

• Manufacturer Part Number: LQ121S1DG61
• Description: TFT Displays & Accessories 12.1 SVGA STRONG 2 LVDS
• Manufacturer: Sharp Microelectronics

Specifications of LQ121S1DG61

• Diagonal: 12.1 in
• Viewing Area (w X H): 247 mmx 184.5 mm
• Pixel Density: 800 x 600
• Module Size (w X H X T): 276 mm x 209 mm x 11 mm
• Backlighting: White
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.Handling Precautions
13. Packing form
l) Connect GND to 4 place of mounting holes to stabilize against EMI and external noise.
m) There are high voltage portions on the backlight and very dangerous. Careless touch may lead to
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
b) Be sure to design the cabinet so that the module can be installed without any extra stress such as
c) Since the front polarizer is easily damaged, pay attention not to scratch it.
d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth
h) Since there is a circuit board in the module back, stress is not added at the time of a design assembly.
i) Protection film is attached to the module surface to prevent it from being scratched .
j) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching
k) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD
n) When handling LCD modules and assembling them into cabinets, please be noted that long-term
o) Cold cathode fluorescent lamp in LCD panel contains a small amount of mercury, please follow local
p) Be careful of a back light lead not to pull by force at the time of the wiring to an inverter,
q) When install LCD modules in the cabinet, please tighten with “torque=0.294±0.02N･m(3.0±0.2kgf･cm)”.
r) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it
s) Notice:Never dismantle the module , because it will cause failure.
t) Be careful when using it for long time with fixed pattern display as it may cause afterimage.
u) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.
v) If a minute particle enters in the module and adheres to an optical material, it may cause display non-
warp or twist.
Handle with care.
Please make it like. If stress is added, there is a possibility that circuit parts may be damaged.
Peel the film off slowly , just before the use, with strict attention to electrostatic charges.
Blow off 'dust' on the polarizer by using an ionized nitrogen.
protective board over the LCD, be careful about the optical interface fringe etc. which degrades
display quality.
panel is used under such environment
storage in the environment of oxidization or deoxidization gas and the use of such materials as
reagent,solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and
discoloration of the LCD modules.
ordinances or regulations for disposal.
or line processing.
gets inside your eye or mouth by mistake.
If adjusted value is changed, the specification may not be satisfied.
uniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if
you intend to install a fan.
electrical shock. When exchange lamps or service, turn off the power without tail.
Product countries / Areas
Piling number of cartons
Package quantity in one carton
Carton size
Total mass of one carton filled
Packing form is shown
when handling.Observe all other precautionary requirements in handling components.
with full modules
JAPAN
388(L) x 334(W) x 263(H)
TAIWAN
10,000g
10pcs
Fig4
6
CHINA
LD18121A-13