AD7732BRU Analog Devices Inc, AD7732BRU Datasheet - Page 13

• Manufacturer Part Number: AD7732BRU
• Description: Analog/Digital Converter IC Number Of Bits:24
• Manufacturer: Analog Devices Inc

Specifications of AD7732BRU

• Interface Type: Serial
• Supply Voltage Max.: 5V
• Package/case: 24-TSSOP
• Leaded Process Compatible: No
• A/d, D/a Features: DSP, MicroWire, QSPI, SPI
• Adc Resolution: 24-Bit
• Rohs Status: RoHS non-compliant
• Number Of Bits: 24
• Sampling Rate (per Second): 15.4k
• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Converters: 1
• Power Dissipation (max): 100mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 28-TSSOP (0.173", 4.40mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: EVAL-AD7732EBZ - BOARD EVAL FOR AD7732
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Pin No.
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Mnemonic
SYNC/P1
RA
RB
BIAS1(+)
AIN1(+)
AIN0(+)
BIAS0(+)
BIAS0(–)
AIN0(–)
AIN1(–)
BIAS1(–)
RC
RD
REFIN(+)
REFIN(–)
AGND
RDY
DOUT
DIN
DV
DGND
DD
Description
SYNC/Digital Input/Digital Output. The pin direction is determined by the P1 DIR bit;
the digital value can be read/written as the P1 bit in the I/O port register. When the
SYNC bit in the I/O port register is set to 1, the SYNC/P1 pin can be used to synchronize
the AD7732 modulator and digital filter with other devices in the system. The digital
voltage is referenced to analog supplies. When configured as an input, the pin should be
tied high or low.
RA, in association with RB and BIAS0(+), can be used to level shift the positive analog
input 0. In normal circuit configuration, this pin is left open circuit.
RB, in association with RA and BIAS0(+), can be used to level shift the positive analog
input 0. In normal circuit configuration, this pin is left open circuit.
This input is used to level shift the positive analog input 1. This signal is used to ensure
that the differential signal seen by the internal buffer amplifier is within its common-
mode range. BIAS pins will normally be connected to 2.5 V.
Positive Analog Input Channel 1.
Positive Analog Input Channel 0.
Voltage Bias for Positive Analog Input 0. This pin has the same function as BIAS1(+).
Voltage Bias for Negative Analog Input 0. This pin has the same function as BIAS1(+).
Negative Analog Input Channel 0.
Negative Analog Input Channel 1.
Voltage Bias for Negative Analog Input 1. This pin has the same function as BIAS1(+).
RC, in association with RD and BIAS0(–), can be used to level shift the negative analog
input 0. In normal circuit configuration, this pin is left open circuit.
RD, in association with RC and BIAS0(–), can be used to level shift the negative analog
input 0. In normal circuit configuration, this pin is left open circuit.
Positive Terminal of the Differential Reference Input. REFIN(+) voltage potential can lie
anywhere between AV
connected to a 2.5 V reference voltage.
Negative Terminal of the Differential Reference Input. REFIN(–) voltage potential can lie
anywhere between AV
connected to a 0 V reference voltage.
Ground Reference Point for Analog Circuitry.
Logic Output. Used as a status output in both conversion mode and calibration mode. In
conversion mode, a falling edge on this output indicates that either any channel or all
channels have unread data available, according to the RDYFN bit in the I/O port register.
In calibration mode, a falling edge on this output indicates that calibration is complete
(see the Digital Interface Description section for more details).
Serial data output with serial data being read from the output shift register on the part.
This output shift register can contain information from any AD7732 register, depending
on the address bits of the communications register.
Serial data input (Schmitt triggered) with serial data being written to the input shift
register on the part. Data from this input shift register is transferred to any AD7732
register, depending on the address bits of the communications register.
Digital Supply Voltage, 3 V or 5 V Nominal.
Ground Reference Point for Digital Circuitry.
Rev. 0 | Page 13 of 32
DD
DD
and AGND. In normal circuit configuration, this pin should be
and AGND. In normal circuit configuration, this pin should be
AD7732