ADSP-BF514KBCZ-4F4 Analog Devices Inc, ADSP-BF514KBCZ-4F4 Datasheet - Page 52

• Manufacturer Part Number: ADSP-BF514KBCZ-4F4
• Description: Low-Pwr BF Proc W/flash & Cnsmr Conctvty
• Manufacturer: Analog Devices Inc
• Series: Blackfin®r
• Type: Fixed Pointr

Specifications of ADSP-BF514KBCZ-4F4

• Interface: I²C, PPI, RSI, SPI, SPORT, UART/USART
• Clock Rate: 400MHz
• Non-volatile Memory: FLASH (4Mbit)
• On-chip Ram: 116kB
• Voltage - I/o: 1.8V, 2.5V, 3.3V
• Voltage - Core: 1.30V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 168-LFBGA
• Architecture: Modified Harvard
• Format: Fixed Point
• Clock Freq (max): 400MHz
• Device Input Clock Speed: 400MHz
• Ram Size: 48KB
• Program Memory Size: 1024KB
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADSP-BF512/BF512F, BF514/BF514F, BF516/BF516F, BF518/BF518F
–10
–20
–30
–40
–50
–60
–10
–15
–20
–10
–20
–30
–40
20
10
–5
60
50
40
30
20
10
20
15
10
40
30
0
5
0
0
0
0
0
Figure 50. Driver Type E Current (3.3V V
Figure 51. Driver Type E Current (2.5V V
Figure 52. Driver Type E Current (1.8V V
0.5
0.5
0.5
1.0
1.0
1.0
1.5
1.5
1.5
SOURCE VOLTAGE (V)
SOURCE VOLTAGE (V)
SOURCE VOLTAGE (V)
2.0
2.0
2.0
DDEXT
DDEXT
DDEXT
2.5
2.5
2.5
V
V
V
/V
/V
/V
V
V
V
V
V
V
DDEXT
DDEXT
DDEXT
DDEXT
DDEXT
DDEXT
DDEXT
DDEXT
DDEXT
DDMEM
DDMEM
DDMEM
3.0
3.0
3.0
Rev. B | Page 52 of 68 | January 2011
= 2.75V @ – 40
= 2.5V @ 25
= 2.25V @ 105
= 1.9V @ – 40
= 1.8V @ 25
= 1.7V @ 105
= 3.6V @ – 40
= 3.3V @ 25
= 3.0V @ 105
)
)
)
V
V
V
OL
OL
OL
3.5
3.5
3.5
° C
° C
° C
° C
° C
° C
° C
° C
° C
TEST CONDITIONS
All timing parameters appearing in this data sheet were mea-
sured under the conditions described in this section.
shows the measurement point for ac measurements (except out-
put enable/disable). The measurement point V
or V
Output Enable Time Measurement
Output signals are considered to be enabled when they have
made a transition from a high impedance state to the point
when they start driving.
The output enable time t
a reference signal reaches a high or low voltage level to the point
when the output starts driving as shown on the right side of
Figure
The time t
signal switches to when the output voltage reaches V
or V
0.95 V, and V
V
nal) = 3.3 V, V
t
the output reaches the V
Time t
If multiple signals (such as the data bus) are enabled, the mea-
surement value is that of the first signal to start driving.
TRIP
TRIP
(MEASURED)
(MEASURED)
t
DDMEM
TRIP
is the interval from when the output starts driving to when
DIS
(high) is 1.3 V and V
V
V
OUTPUT
ENA
INPUT
54.
OH
OL
(low). For V
OUTPUT STOPS DRIVING
OR
is calculated as shown in the equation:
/2 for V
ENA_MEASURED
Measurements (Except Output Enable/Disable)
TRIP
Figure 53. Voltage Reference Levels for AC
TRIP
V
t
MEAS
ENA
(low) is 0.85 V. For V
Figure 54. Output Enable/Disable
DDEXT
(high) is 1.7 V, and V
REFERENCE
t
V
V
DIS_MEASURED
DDEXT
OH
OL
SIGNAL
=
t
(MEASURED) - ΔV
DECAY
(MEASURED) + ΔV
is the interval from when the reference
/V
TRIP
t
ENA
ENA_MEASURED
(nominal) = 1.8 V, V
DDMEM
TRIP
(high) or V
is the interval from the point when
HIGH IMPEDANCE STATE
(low) is 1.2 V. For V
t
(nominal) = 1.8 V/2.5 V/3.3 V.
ENA
DDEXT
TRIP
OUTPUT STARTS DRIVING
TRIP
–
(low) trip voltage.
t
TRIP
(low) is 1.6 V. Time
(nominal) = 2.5 V,
t
MEAS
TRIP
ENA_MEASURED
V
V
TRIP
TRIP
t
TRIP
(high) is
DDEXT
is V
(LOW)
V
(HIGH)
V
TRIP
OH
OL
Figure 53
V
(MEASURED)
(MEASURED)
DDEXT
MEAS
(high)
(nomi-
/2