CY8C3866LTI-067 Cypress Semiconductor Corp, CY8C3866LTI-067 Datasheet - Page 63

no-image

CY8C3866LTI-067

Manufacturer Part Number
CY8C3866LTI-067
Description
CY8C3866LTI-067
Manufacturer
Cypress Semiconductor Corp
Series
PSOC™ 3 CY8C38xxr
Datasheets

Specifications of CY8C3866LTI-067

Core Processor
8051
Core Size
8-Bit
Speed
67MHz
Connectivity
EBI/EMI, I²C, LIN, SPI, UART/USART, USB
Peripherals
CapSense, DMA, POR, PWM, WDT
Number Of I /o
25
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Eeprom Size
2K x 8
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
1.71 V ~ 5.5 V
Data Converters
A/D 2x20b, D/A 4x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
CY8C3866LTI-067
Manufacturer:
Cypress
Quantity:
260
9.2 Serial Wire Debug Interface
The SWD interface is the preferred alternative to the JTAG
interface. It requires only two pins instead of the four or five
needed by JTAG. SWD provides all of the programming and
debugging features of JTAG at the same speed. SWD does not
provide access to scan chains or device chaining. The SWD
clock frequency can be up to 1/3 of the CPU clock frequency.
SWD uses two pins, either two of the JTAG pins (TMS and TCK)
or the USBIO D+ and D– pins. The USBIO pins are useful for in
system programming of USB solutions that would otherwise
require a separate programming connector. One pin is used for
the data clock and the other is used for data input and output.
Document Number: 001-11729 Rev. *S
    V
2
3
1
4
PSoC 3 should be at the same voltage level as Host V
powered by V
programming. Rest of PSoC 3 voltage domains ( V
voltage level as host Programmer.
the capability to toggle power (Vddd, Vdda, All Vddio’s) to PSoC 3. This may typically require external
interface circuitry to toggle power which will depend on the programming setup. The power supplies can
be brought up in any sequence, however, once stable, VDDA must be greater than or equal to all other
supplies.
devices with dedicated XRES pin, P1[2] is GPIO pin by default. So use P1[2] as Reset pin only for 48-
pin devices, but use dedicated XRES pin for rest of devices.
Vdda must be greater than or equal to all other power supplies (Vddd, Vddio’s) in PSoC 3.
For Power cycle mode Programming, XRES pin is not required. But the Host programmer must have
The voltage levels of the Host Programmer and the PSoC 3 voltage domains involved in Programming
should be the same. XRES pin (XRES_N or P1[2]) is powered by V
powered by V
P1[2] will be configured as XRES by default only for 48-pin devices (without dedicated XRES pin). For
DDIO2
, V
Host Programmer
DDIO3
) need not be at the same voltage level as host Programmer. The Port 1 SWD pins are
DDIO1
DDD
Figure 9-2. SWD Interface Connections between PSoC 3 and Programmer
. So for Programming using the USB SWD pins with XRES pin, the V
. So V
DDIO1
SWDCK
SWDIO
XRES
of PSoC 3 should be at same voltage level as host V
V
GND
DD
GND
V
DD
DDD
,  V
DD
. Rest of PSoC 3 voltage domains ( V
DDA
SWD can be enabled on only one of the pin pairs at a time. This
only happens if, within 8 µs (key window) after reset, that pin pair
(JTAG or USB) receives a predetermined sequence of 1s and 0s.
SWD is used for debugging or for programming the flash
memory.
The SWD interface can be enabled from the JTAG interface or
disabled, allowing its pins to be used as GPIO. Unlike JTAG, the
SWD interface can always be reacquired on any device during
the key window. It can then be used to reenable the JTAG
interface, if desired. When using SWD or JTAG pins as standard
GPIO, make sure that the GPIO functionality and PCB circuits do
not interfere with SWD or JTAG use.
, V
DDIO0
, V
DDIO2
DDIO1
V
XRES or P1[2]  
SWDCK (P1[1] or P15[7])
SWDIO (P1[0] or P15[6])
V
SSD
DDD
, V
, V
. The USB SWD pins are
, V
DDIO3
SSA
DDA
PSoC
) need not be at the same
, V
DDIO0
3, 4
DD
, V
for Port 1 SWD
PSoC 3
DDIO1
DDD
®
, V
, V
3: CY8C38 Family
DDIO2
DDIO1 
DDA
, V
, V
of
DDIO3
DDIO0
1, 2, 3
Data Sheet
,  
Page 63 of 130
[+] Feedback

Related parts for CY8C3866LTI-067