KSZ8842-PMBL Micrel Inc, KSZ8842-PMBL Datasheet - Page 43

• Manufacturer Part Number: KSZ8842-PMBL
• Description: 2-Port Ethernet Switch/Repeater + 32-bit/33MHz PCI Bus Interface ( )
• Manufacturer: Micrel Inc

Specifications of KSZ8842-PMBL

• Controller Type: Ethernet Switch Controller
• Interface: PCI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 100-LFBGA
• Number Of Primary Switch Ports: 2
• Internal Memory Buffer Size: 32
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Phy/transceiver Interface: MII
• Power Supply Type: Analog/Digital
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Commercial
• Data Rate: 100Mbps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-1636 - BOARD EVALUATION KSZ8842-PMQL
• Current - Supply: -
• Lead Free Status / RoHS Status: Supplier Unconfirmed, Lead free / RoHS Compliant
• Other names: 576-3089

Micrel, Inc.
The following table shows the access rules of the register.
PCI Control & Status Registers
The PCI CSR registers are all 32 bit in Little Endian format. For PCI register Read cycle, the KSZ8842-PMQL/PMBL
allows any different combination of CBEN. For PCI register bus cycles, only byte, word (16-bit), or Dword (32-bit)
accesses are allowed. Any other combinations are illegal, and will be target aborted.
MAC DMA Transmit Control Register (MDTXC Offset 0x0000)
The MAC DMA transmit control register establishes the transmit operating modes and commands for the port. This
register should be one of the last CSRs to be written as part of the transmit initialization.
The following table shows the register bit fields.
October 2007
Category
Value after hardware reset
31 – 30
29 – 24
23 – 19
15 – 10
7 – 0
Bit
Bit
18
17
16
Default
0x00
0x00
0x00
0
0
0
-
Default
0x00
R/W
RW
RW
RW
RW
RO
RO
RO
Description
Reserved
MTBS DMA Transmit Burst Size
This field indicates the maximum number of words to be transferred in one
DMA transaction. If reset, the MAC DMA burst size is limited only by the
amound of data stored in the transmit buffer before issuing a bus request. The
MTBS can be programmed with the following permissible values: 0,1, 2, 4, 8,
16, or 32.
After reset, the MTBS default is 0, i.e., unlimited.
Reserved
MTUCG MAC Transmit UDP Checksum Generate
When set, the KSZ8842-PMQL/PMBL will generate correct UDP checksum for
outgoing UDP/IP frames at port.
When this bit is set, ADD CRC should also turn on.
MTTCG MAC Transmit TCP Checksum Generate
When set, the KSZ8842-PMQL/PMBL will generate correct TCP checksum for
outgoing TCP/IP frames at port.
When this bit is set, ADD CRC should also turn on.
MTICG MAC Transmit IP Checksum Generate
When set, the KSZ8842-PMQL/PMBL will generate correct IP checksum for
outgoing IP frames at port.
When this bit is set, ADD CRC should also turn on.
Reserved
Description
Interrupt Line
Provides interrupt line routing information. The basic input/output system
(BIOS) writes the routing information into to this field when it initialized and
configures the system.
The value in this field indicates which input of the system interrupt controller is
connected to the KSZ8842-PMQL/PMBL’s interrupt pin/ball. The driver uses
this information to determine priority and vector information. Values in this field
are system architecture specific.
Description
0x281401XX
43
KSZ8842-PMQL/PMBL
M9999-100207-1.5