CYII5FM1300AA-QDC Cypress Semiconductor Corp, CYII5FM1300AA-QDC Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/1/179/cypress_semiconductor_corp_sml.jpg)
CYII5FM1300AA-QDC
Manufacturer Part Number
CYII5FM1300AA-QDC
Description
IC SENSOR IMAGE 1.3MP 84-LCC
Manufacturer
Cypress Semiconductor Corp
Type
CMOS Imagingr
Specifications of CYII5FM1300AA-QDC
Pixel Size
6.7µm x 6.7µm
Active Pixel Array
1280H x 1024V
Frames Per Second
27
Voltage - Supply
3 V ~ 4.5 V
Package / Case
84-LCC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Table 18. Multiple Slope Register Settings
NROF_PIXELS Register (11:0)
After the internal x_sync is generated (start of the pixel readout
of a particular row), the PIXEL_VALID signal goes high. The
PIXEL_VALID signal goes low when the pixel counter reaches
the value loaded in the NROF_PIXEL register. Due to the fact
that two pixels are read at the same clock cycle, you must divide
this number by 2 (NROF_PIXELS = (width of ROI / 2) – 1).
ROF_LINES Register (11:0)
After the internal yl_sync is generated (start of the frame readout
with Y_START), the line counter increases with each Y_CLOCK
pulse until it reaches the value loaded in the NROF_LINES
register and generates a LAST_LINE pulse. It must be noted that
Document #: 38-05710 Rev. *H
6. External Pixel Reset Voltage for Multiple Slope (bit 11)
Bits KNEE_POINT_MSB and KNEE_POINT_LSB select the
on chip-generated pixel reset voltage.
Bit KNEE_POINT_ENABLE set to ’1’ switches control to the
right side of the image core so the pixel reset voltage
(VDDR_RIGHT), selected by bits KNEE_POINT_MSB/LSB,
is used.
Use bit KNEE_POINT_ENABLE only for multiple slope oper-
ation in synchronous shutter mode. In rolling shutter mode,
use only the bits KNEE_POINT_MSB/LSB to select the sec-
ond knee-point in dual slope operation. The actual knee-point
depends on VDDH, VDDR_LEFT and VDDC applied to the
sensor.
Setting bit VDDR_RIGHT_EXT to ’1’ disables the circuit that
generates the variable pixel reset voltage and uses the volt-
age externally applied to pin VDDR_RIGHT as the dou-
ble/multiple slope reset voltage.
Setting bit VDDR_RIGHT_EXT to ’0’ allows you to monitor the
variable pixel reset voltage (used for multiple slope operation)
on pin VDDR_RIGHT.
MSB/LSB
KNEE_POINT
00
01
10
11
ENABLE
0 or 1
s h ift-r e g is te r
S y n c o f le ft
1
1
1
Pixel Reset Voltage
VDDR_LEFT – 0.76
VDDR_LEFT – 1.52
VDDR_LEFT – 2.28
Figure 18. Synchronization of Shift Registers in Rolling Shutter Mode
(V)VDDR_RIGHT
VDDR_LEFT
L in e n
Knee-point
+ 0.76
+ 1.52
+ 2.28
S y n c o f r ig h t
s h ift-r e g is te r
(V)
0
the value loaded in the register must be (Number of lines
required - 1).
INT_TIME Register (11:0)
Use the INT_TIME register to set the integration time of the
electronic shutter. The interpretation of the INT_TIME depends
on the chosen shutter type (rolling or synchronous).
■
■
Global shutter
Rolling shutter
After the SS_START pulse is applied an internal counter
counts the number of SS granulated clock cycles until it
reaches the value loaded in the INT_TIME register and gen-
erates a TIME_OUT pulse. Use this TIME_OUT pulse to gen-
erate the SS_STOP pulse to stop the integration. When the
INT_TIME register is used, the maximum integration time is:
TINT_MAX = 212 × 256 (maximum granularity) × (40 MHZ)
– 1 = 26.2 ms.
You can increase this maximum time if you use an external
counter to trigger SS_STOP. Ten is the minimal value that you
can load into the INT_TIME register (see also
granularities (bits 4, 5, 6 and 7)
When the Y_START pulse is applied (start of the frame read-
out), the sequencer generates the yl_sync pulse for the left
Y-shift register (read out Y-shift register). This loads the left
Y-shift register with the pointer loaded in YL_REG register. At
each Y_CLOCK pulse, the pointer shifts to the next row and
the integration time counter increases until it reaches the val-
ue loaded in the INT_TIME register. At that moment, the se-
quencer generates the yr_sync pulse for the right Y-shift reg-
ister; it loads the right Y-shift register (reset Y-shift register)
with the pointer loaded in YR_REG register (see
The integration time counter is reset when the sync for the left
Y-shift register, yl_sync is asserted. Both shift registers keep
moving until the next sync is asserted, i.e., the yl_sync for the
left Y-shift register (generated by Y_START) and the yr_sync
for the right Y-shift register (generated when the integration
time counter reaches the INT_TIME value).
Treg_int Difference between the left and right pointer = value
set in the INT_TIME register (number of lines).
The actual integration time is given by
Tint Integration time [# lines] = NROF_LINES register
– INT_TIME register.
Tint Integration time [# lines] = NROF_LINES register
– INT_TIME register.
T
re g _ in t
S y n c
L a s t lin e , fo llo w e d b y
s y n c o f le ft s h ift- re g is te r
on page 17).
CYII5SM1300AB
T
in t
Page 18 of 35
Internal clock
Figure
18).
[+] Feedback