CS1D-DPL02D Omron, CS1D-DPL02D Datasheet - Page 224
CS1D-DPL02D
Manufacturer Part Number
CS1D-DPL02D
Description
CS1D Dual IO Exp
Manufacturer
Omron
Datasheet
1.CS1D-SP002.pdf
(638 pages)
Specifications of CS1D-DPL02D
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 224 of 638
- Download datasheet (12Mb)
Making Settings from the CX-Programmer
6-1-2
Overview of PLC Setup
The input response time settings for Basic I/O Units must be changed in the
following cases:
• Chattering or noise occur in CS-series Basic I/O Units.
• Short pulse inputs are being received for intervals longer than the cycle
Data in all regions of I/O Memory (including the CIO Area, Work Areas,
Timer Flags and PVs, Task Flags, Index Registers, and Data Registers)
must be retained when the PLC’s power is turned ON.
The status of bits force-set or force-reset from a Programming Device
(including Programming Consoles) must be retained when the PLC’s power
is turned on.
• You do not want the operating mode to be determined by the Programming
• You want the PLC to go into RUN mode or MONITOR mode and start oper-
• You want the operating mode to be other than PROGRAM mode when the
Disabling detection of low-battery errors when it is not required.
Detecting interrupt-task errors is not required.
Data files are required but a Memory Card cannot be used or the files are
written frequently. (Part of the EM Area will be used as file memory.)
time.
Console’s mode switch setting at startup.
ating immediately after startup.
power is turned ON.
Settings Other Than Those for Duplex Systems
Cases when settings must be changed
5. This function is supported only by Duplex CPU Units with Unit Ver. 1.3 or
6. As of October 2006, these settings can be selected with the Programming
When using CX-Programmer version 3.0 or higher, set the device type to
“CS1H-H” in the PLC Setup and select Duplex Settings from the Options
Menu on the PLC Settings Window to enable setting the PLC Setup for a
CS1D.
When using CX-Programmer version 4.0 or higher and the device type is set
to “CS1S-H” or “CS1D-S,” is it not necessary to select Duplex Settings from
the Options Menu on the PLC Settings Window to enable setting the PLC
Setup for a CS1D.
The following table lists cases in which the PLC Setup must be changed for
aspects of operation not directly related to duplex operation.
later.
Console only. The settings will be added to the CX-Programmer in the next
version upgrade. The settings will be added to CX-Programmer version 7.0
when its functions are expanded by auto-update.
Basic I/O Unit Input Response Time
IOM Hold Bit Status at Startup
Forced Status Hold Bit Status at Startup
Startup Mode
Detect Low Battery
Detect Interrupt Task Error (See note.)
EM File Memory
Setting(s) to be changed
Section 6-1
189
Related parts for CS1D-DPL02D
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
CS1D Dual IO Control Unit
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
CS1D Dual IO Interface Unit
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
CS1D Dual CPU Exp
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
CS1D Dual Exp Rack
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: