LAN8700IC-AEZG-TR SMSC, LAN8700IC-AEZG-TR Datasheet - Page 13
![Ethernet ICs Hi Perform Ethernet PHY](/photos/16/2/160288/landingpagesmsclan8700-2_sml.jpg)
LAN8700IC-AEZG-TR
Manufacturer Part Number
LAN8700IC-AEZG-TR
Description
Ethernet ICs Hi Perform Ethernet PHY
Manufacturer
SMSC
Type
MII/RMII Ethernet Transceiverr
Datasheet
1.LAN8700C-AEZG.pdf
(80 pages)
Specifications of LAN8700IC-AEZG-TR
Ethernet Connection Type
10 Base-T, 100 Base-TX
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Product
Ethernet Transceivers
Number Of Transceivers
1
Standard Supported
802.3ab
Data Rate
10 Mbps, 100 Mbps
Supply Voltage (max)
3.3 V
Supply Voltage (min)
1.8 V
Supply Current (max)
39 mA, 81.6 mA
Maximum Operating Temperature
+ 70 C
Package / Case
QFN-36
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LAN8700IC-AEZG-TR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR
Datasheet
SMSC LAN8700/LAN8700i
SIGNAL NAME
nINTSEL
TX_CLK
MODE0
MODE1
MODE2
RXD0/
RXD1/
RXD2/
RXD3/
TYPE
IOPU
IOPU
IOPU
IOPU
Table 3.1 MII Signals (continued)
O
DATASHEET
Transmit Clock: 25MHz in 100Base-TX mode. 2.5MHz in
10Base-T mode.
Note:
Note:
Receive Data 0: Bit 0 of the 4 data bits that are sent by the PHY
in the receive path.
PHY Operating Mode Bit 0: set the default MODE of the PHY.
Note:
Receive Data 1: Bit 1 of the 4 data bits that are sent by the PHY
in the receive path.
PHY Operating Mode Bit 1: set the default MODE of the PHY.
Note:
Receive Data 2: Bit 2 of the 4 data bits that are sent by the PHY
in the receive path.
PHY Operating Mode Bit 2: set the default MODE of the PHY.
Notes:
Receive Data 3: Bit 3 of the 4 data bits that are sent by the PHY
in the receive path.
nINTSEL: On power-up or external reset, the mode of the
nINT/TXER/TXD4 pin is selected.
Notes:
RXD2 is not used in RMII Mode.
See
the MODE options.
When RXD3/nINTSEL is floated or pulled to VDDIO, nINT is
selected for operation on pin nINT/TXER/TXD4 (default).
When RXD3/nINTSEL is pulled low to VSS through a resistor,
(see
page
nINT/TXER/TXD4.
RXD3 is not used in RMII Mode
If the nINT/TXER/TXD4 pin is configured for nINT mode, then
a pull-up resistor is needed to VDDIO on the nINT/TXER/TXD4
pin. see
page
See
for additional information on configuration/strapping options.
®
Section 5.4.9.2, "Mode Bus – MODE[2:0]," on page
Section 4.10, "nINT/TX_ER/TXD4 Strapping," on page 31
13
Table 4.3, “Boot Strapping Configuration Resistors,” on
Technology in a Small Footprint
32), TXER/TXD4 is selected for operation on pin
32.
This signal is not used in RMII Mode.
For proper TXCLK operation, RX_ER and RX_DV must
NOT be driven high externally on a hardware reset or
on a LAN8700 power up.
See
page
See
page
Table 4.3, “Boot Strapping Configuration Resistors,” on
Section 5.4.9.2, "Mode Bus – MODE[2:0]," on
Section 5.4.9.2, "Mode Bus – MODE[2:0]," on
54, for the MODE options
54, for the MODE options.
DESCRIPTION
Revision 2.2 (12-04-09)
54, for