COM20019I3V-HT SMSC, COM20019I3V-HT Datasheet - Page 29

• Manufacturer Part Number: COM20019I3V-HT
• Description: Network Controller & Processor ICs ARCNET Contrllr
• Manufacturer: SMSC

Specifications of COM20019I3V-HT

• Product: Controller Area Network (CAN)
• Number Of Transceivers: 1
• Data Rate: 312.5 Kbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 3 V
• Supply Current (max): 25 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Package / Case: TQFP-48
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6.2.13 Setup 2 Register
Note 6.1
SMSC COM20019I 3.3V
Cost Competitive ARCNET (ANSI 878.1) Controller with 2K x 8 On-Chip RAM
7
6,5
4
3
BIT
The Setup 2 Register is new to the COM20019I 3V. It is an 8-bit read/write register accessed when the
Sub Address Bits SUBAD[2:0] are set up accordingly (see the bit definitions of the Sub Address Register).
This register contains bits for various functions. The RBUSTMG bit is used to Disable/Enable Fast Read
function for High Speed CPU bus support. The EF bit is used to enable the new timing for certain functions
in the COM20019I 3V (if EF = 0, the timing is the same as in the COM20020 Rev. B). See Appendix “A”.
The NOSYNC bit is used to enable the NOSYNC function during initialization. If this bit is reset, the line
has to be idle for the RAM initialization sequence to be written. If set, the line does not have to be idle for
the initialization sequence to be written. See Appendix “A”.
The RCNTM[1,0] bits are used to set the time-out period of the recon timer. Programming this timer for
shorter time periods has the benefit of shortened network reconfiguration periods. The time periods shown
in the table on the following page are limited by a maximum number of nodes in the network. These time-
out period values are for 312.5 Kbps. For other data rates, scale the time-out period time values
accordingly; the maximum node count remains the same.
The node ID value 255 must exist in the network for the 420 mS time-out to be valid.
Receiver
Inhibited
(Reserved)
Power On Reset POR
Test
BIT NAME
RCNTM1
0
0
1
1
SYMBOL
RI
TEST
RCNTM0
0
1
0
1
This bit, if high, indicates that the receiver is not enabled because
either an "Enable Receive to Page fnn" command was never
issued, or a packet has been deposited into the RAM buffer page
fnn as specified by the last "Enable Receive to Page fnn"
command. No messages will be received until this command is
issued, and once the message has been received, the RI bit is
set, thereby inhibiting the receiver. The RI bit is cleared by
issuing an "Enable Receive to Page fnn" command. This bit,
when set, will cause an interrupt if the corresponding bit of the
Interrupt Mask Register (IMR) is also set. When this bit is set and
another station attempts to send a packet to this station, this
station will send a NAK.
These bits are undefined.
This bit, if high, indicates that the COM20019I 3V has been reset
by either a software reset, a hardware reset, or writing 00H to the
Node ID Register. The POR bit is cleared by the "Clear Flags"
command.
This bit is intended for test and diagnostic purposes. It is a logic
"0" under normal operating conditions.
Table 6.3 - Status Register
DATASHEET
TIME-OUT PERIOD
Page 29
420 mS*
840 mS
6.72 S
1.68 S
DESCRIPTION
Up to 255 nodes
Up to 64 nodes
Up to 32 nodes
Up to 16 nodes
(See Note 6.1)
MAX NODE
COUNT
Rev. 11-07-08