DS26528G Maxim Integrated Products, DS26528G Datasheet - Page 32
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS26528G
Manufacturer Part Number
DS26528G
Description
Network Controller & Processor ICs Octal E1-T1-J1 Singl e-Chip Transceiver (
Manufacturer
Maxim Integrated Products
Datasheet
1.DS26528G.pdf
(276 pages)
Specifications of DS26528G
Product
Framer
Number Of Transceivers
8
Supply Voltage (max)
3.465 V
Supply Voltage (min)
3.135 V
Supply Current (max)
875 mA
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Package / Case
TE-CSBGA
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS26528GA2
Manufacturer:
AFATECH
Quantity:
3 623
Part Number:
DS26528GA2
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
DS26528GA5+
Manufacturer:
Maxim Integrated
Quantity:
10 000
8.8
The DS26528 provides a versatile backplane interface that can be configured to the following:
8.8.1
The DS26528 contains dual two-frame elastic stores: one for the receive direction and one for the transmit
direction. Both elastic stores are fully independent. The transmit- and receive-side elastic stores can be
enabled/disabled independently of each other. Also, the transmit or receive elastic store can interface to either a
1.544MHz or 2.048/4.096/8.192/16.384MHz backplane without regard to the backplane rate for the other elastic
store. Since the DS26528 has a common TSYSCLK and RSYSCLK for all eight ports, the backplane signals in
each direction must be synchronous for all ports on which the elastic stores are enabled. However, the transmit
and receive signals are not required to be synchronous to each other. The TIOCR and RIOCR settings should be
identical for all ports on which the elastic stores are enabled.
The elastic stores have two main purposes. First, they can be used for rate conversion. When the DS26528 is in
the T1 mode, the elastic stores can rate convert the T1 data stream to a 2.048MHz backplane. In E1 mode the
elastic store can rate convert the E1 data stream to a 1.544MHz backplane. Second, the elastic stores can be used
to absorb the differences in frequency and phase between the T1 or E1 data stream and an asynchronous (i.e., not
locked) backplane clock, which can be 1.544MHz or 2.048MHz. In this mode, the elastic stores manage the rate
difference and perform controlled slips, deleting or repeating frames of data to manage the difference between the
network and the backplane.
If the elastic store is enabled while in E1 mode, then either CAS or CRC-4 multiframe boundaries are indicated via
the RMSYNC output as controlled by the RSMS2 control bit (RIOCR.1). If the user selects to apply a 1.544MHz
clock to the RSYSCLK pin, then the Receive Blank Channel Select registers (RBCS1:RBCS4) registers determine
which channels of the received E1 data stream will be deleted. In this mode an F-bit location is inserted into the
RSER data and set to 1. Also, in 1.544MHz applications, the RCHBLK output will not be active in Channels 25 to
32 (or in other words, RCBR4 is not active). If the two-frame elastic buffer either fills or empties, a controlled slip
occurs. If the buffer empties, a full frame of data is repeated at RSER and the RLS4.5 and RLS4.6 bits are set to 1.
If the buffer fills, a full frame of data is deleted and the RLS4.5 and RLS4.7 bits are set to 1.
The elastic stores can also be used to multiplex T1 or E1 data streams into higher backplane rates. This is the
Interleave Bus Option (IBO), which is discussed in Section 8.8.2.
elastic stores.
Table 8-2. Registers Related to the Elastic Store
Note: The addresses shown are for Framer 1. Addresses for Framers 2 to 8 can be calculated using the following: Framer n = (Framer 1
address + (n - 1) x 200h), where n = 2 to 8 for Framers 2 to 8.
Receive I/O Configuration Register (RIOCR)
Receive Elastic Store Control Register
(RESCR)
Receive Latched Status Register 4 (RLS4)
Receive Interrupt Mask Register 4 (RIM4)
Transmit Elastic Store Control Register
(TESCR)
Transmit Latched Status Register 1 (TLS1)
Transmit Interrupt Mask Register 1 (TIM1)
•
•
•
•
•
•
•
•
System Backplane Interface
Transmit and receive two-frame elastic stores
Mapping of T1 channels into a 2.048MHz backplane
IBO mode for multiple framers to share the backplane signals
Transmit and receive channel-blocking capability
Fractional T1/E1/J1 support
Hardware-based (through the backplane interface) or processor-based signaling
Flexible backplane clock providing frequencies of 2.048MHz, 4.096MHz, 8.192MHz, 16.384MHz
Backplane clock and frame pulse (TSSYNCIOn) generator
Elastic Stores
REGISTER
32 of 276
ADDRESSES
FRAMER
0A3h
1A0h
084h
085h
093h
185h
190h
Table 8-2
Sync and clock selection for the receiver.
Receive elastic store control.
Receive elastic store empty full status.
Receive interrupt mask for elastic store.
Transmit elastic control such as minimum
mode.
Transmit elastic store latched status.
Transmit elastic store interrupt mask.
DS26528 Octal T1/E1/J1 Transceiver
shows the registers related to the
FUNCTION