FLUKE-772 Fluke, FLUKE-772 Datasheet
![MULTIMETER, DIGITAL, CLAMP](/photos/27/67/276721/4601796_sml.jpg)
FLUKE-772
Specifications of FLUKE-772
FLUKE-772 Summary of contents
Page 1
... Milliamp Process Clamp Meter Introduction The hand-held, battery-operated Fluke 772 and 773 Milliamp Process Clamp Meters (the Meter) can be used in troubleshooting transmitters, valves, PLC and DCS I/O. Unlike conventional clamp meters, the Meter features a remote jaw that is connected to the main body via extension cable ...
Page 2
... Soft carrying case TL75 test leads AC 72 detachable clip TL 940 mini hook test leads Instruction sheet Contacting Fluke To contact Fluke, call one of the following telephone numbers: Technical Support USA: 1-800-44-FLUKE (1-800-443-5853) Calibration/Repair USA: 1-888-99-FLUKE (1-888-993-5853) Canada: 1-800-36-FLUKE (1-800-363-5853) Europe: +31 402-675-200 Japan: +81-3-3434-0181 ...
Page 3
... Risk of Electrical Shock. X Equipment protected by double or reinforced insulation. T Battery B Conforms to relevant European Union directives (Direct Current) F Earth Ground not dispose of this product as unsorted municipal waste Fluke’s website for recycling information. ; Conforms to relevant Australian standards. ) Conforms to relevant Canadian and US standards. Table 1. Symbols Explanation ...
Page 4
Getting Acquainted with the Meter Figures 1-4 explain the Meter’s features, buttons, input/output jacks, and display Number Turns the Meter on and off A Measurement spotlight LED button B Turns the display backlight on and off ...
Page 5
Number Detachable clamp A Tactile Barrier docked and un-docked. Refer to “Safety Information B and Symbols”. Display C Measurement spotlight LED D Figure 2. The Milliamp Process Clamp Meter 1 773 MILLIAMP PROCESS CLAMP METER Description 2 3 Fjv05.eps ...
Page 6
MAX 15 14 Number Main display values A HOLD is activated B Clamp is active C Test lead jack indicator. Test lead connection is required. D HART 250 E Shift is active F Reading is scaled G Loop ...
Page 7
Number Voltage measurement test lead input, also used for voltage A sourcing HI. Common test lead input, also used for voltage sourcing LO. B -mA test lead input, also used for mA sourcing. C +mA test lead ...
Page 8
... To exit ramping, press any button. Probe Holder The Meter is equipped with a probe holder that can either hold a test probe or can be used to attach the Fluke ToolPak. See Figure 5. XW Warning Figure 5. The Probe Holder Fjv08.eps ...
Page 9
To avoid electric shock, do not use the clamp on non- insulated conductors. Measurements can be taken with the clamp in the docked position, remotely using the 1 m cable, or via test leads. For accurate measurements: Always zero the ...
Page 10
To use the test leads for measurements: 1. Insert the test leads into the proper input jacks. See Figure 7. 2. Press the correct button for the measurement. 3. Apply the test leads. 4. Observe the reading on the main ...
Page 11
To enter mA Source mode for the 773, see Figure 8: 1. Insert the test leads into the desired input jacks. 2. Press Press until Source appears on the display. Simulating mA Output In Simulate mode, the ...
Page 12
Loop Supply In Loop Supply mode, the Meter powers a transmitter while measuring the mA signal. To enter Loop Supply mode, see Figure 10: 1. Insert the test leads into the LOOP PWR jacks. See Figure 10. 2. Press N. ...
Page 13
To avoid possible electric shock or personal injury, repairs or servicing not covered in this manual should be performed only by qualified personnel. Cleaning the Meter To avoid electrical shock, remove any input signals before cleaning. To avoid damaging the ...
Page 14
Electrical Specifications Current Measurement With Jaw Ranges ................................ 0-20.99 mA; 21-100 mA Resolution............................ 0.01 mA; 0.1 mA Accuracy.............................. 0 counts counts In Circuit Range .................................. 0-24 mA Resolution............................ 0.01 mA Accuracy.............................. 0 ...
Page 15
Environmental Specifications Operating Temperature ............. -10 ~50 C Storage Temperature................. -25 ~60 C Operating Humidity .................... < <30 C ;< ~50 C Operating Altitude ...................... 0 ~ 2000 m IP Rating.................................... IP 40 ...
Page 16
... See the 772/773 Service Information Sheet for part numbers and procedures. LIMITED WARRANTY & LIMITATION OF LIABILITY This Fluke product will be free from defects in material and workmanship for 3 years (one year for cable and clamp) from the date of purchase. This warranty does not cover fuses, disposable batteries or damage from accident, neglect, misuse or abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Fluke’ ...