ATF-35143-BLKG Avago Technologies US Inc., ATF-35143-BLKG Datasheet
ATF-35143-BLKG
Specifications of ATF-35143-BLKG
ATF-35143-BLKG
Available stocks
Related parts for ATF-35143-BLKG
ATF-35143-BLKG Summary of contents
Page 1
... Low Noise Pseudomorphic HEMT in a Surface Mount Plastic Package Data Sheet Description Avago’s ATF-35143 is a high dynamic range, low noise, PHEMT housed in a 4-lead SC-70 (SOT-343) surface mount plastic package. Based on its featured performance, ATF-35143 is suitable for applications in cellular and PCS base stations, LEO ...
Page 2
... ATF-35143 Absolute Maximum Ratings Symbol Parameter V Drain - Source Voltage DS V Gate - Source Voltage GS V Gate Drain Voltage [ Drain Current [ Total Power Dissipation diss P RF Input Power in max T Channel Temperature CH T Storage Temperature STG θ Thermal Resistance [5] jc Product Consistency Distribution Charts 120 +0 ...
Page 3
... ATF-35143 Electrical Specifications T = 25°C, RF parameters measured in a test circuit for a typical device A Symbol Parameters and Test Conditions I [1] Saturated Drain Current dss V [1] Pinchoff Voltage P I Quiescent Bias Current d g [1] Transconductance m I Gate to Drain Leakage Current GDO I Gate Leakage Current ...
Page 4
... ATF-35143 Typical Performance Curves 30 OIP3 1dB (mA) DSQ [1,2] Figure 6. OIP3 and P vs. Bias at 2 GHz. 1dB (mA) DSQ [1] Figure 8. NF and G vs. Bias at 2 GHz (mA) DS Figure 10. P vs. Bias (Active Bias) 1dB [1] Tuned for GHz. Notes: 1. Measurements made on a fixed tuned production test board that was tuned for optimal gain match with reasonable noise figure bias ...
Page 5
... ATF-35143 Typical Performance Curves, 1.50 1.25 1.00 0. FREQUENCY (GHz) Figure 12. F vs. Frequency and Current at 2V. min 25C -40C 16 85C FREQUENCY (GHz) Figure 14. F and G vs. Frequency and min a Temperature, V =2V, I =15 mA 1dB 5 OIP3 Gain (mA) DS Figure 16. OIP3 and Gain vs. Bias ...
Page 6
... ATF-35143 Typical Noise Parameters Γ Freq. F min opt GHz dB Mag. 0.5 0.10 0.91 0.9 0.12 0.87 1.0 0.14 0.86 1 ...
Page 7
... ATF-35143 Typical Noise Parameters Γ Freq. F min opt GHz dB Mag. 0.5 0.10 0.88 0.9 0.11 0.84 1.0 0.12 0.83 1 ...
Page 8
... GHz and higher are based on measurements while the F min a set of 16 noise figure measurements made at 16 different impedances using an ATF NP5 test system. From these measurements a true F calculated. Refer to the noise parameter application section for more information and noise parameters are measured on a microstrip line made on 0.025 inch thick alumina carrier. The input reference plane is at the end of the gate lead ...
Page 9
... GHz and higher are based on measurements while the F min a set of 16 noise figure measurements made at 16 different impedances using an ATF NP5 test system. From these measurements a true F calculated. Refer to the noise parameter application section for more information and noise parameters are measured on a microstrip line made on 0.025 inch thick alumina carrier. The input reference plane is at the end of the gate lead ...
Page 10
... ATF-35143 Typical Noise Parameters Γ Freq. F min opt GHz dB Mag. 0.5 0.12 0.87 0.9 0.16 0.82 1.0 0.17 0.81 1 ...
Page 11
... ATF-35143 Typical Noise Parameters Γ Freq. F min opt GHz dB Mag. 0.5 0.11 0.86 0.9 0.15 0.81 1.0 0.16 0.80 1 ...
Page 12
... ATF-35143 Typical Noise Parameters Γ Freq. F min opt GHz dB Mag. 0.5 0.11 0.87 0.9 0.16 0.81 1.0 0.17 0.79 1 ...
Page 13
... ATF-35143 Typical Noise Parameters Γ Freq. F min opt GHz dB Mag. 0.5 0.10 0.90 0.9 0.14 0.85 1.0 0.16 0.83 1 ...
Page 14
... ATF-35143 Typical Noise Parameters Γ Freq. F min opt GHz dB Mag. 0.5 0.22 0.84 0.9 0.30 0.78 1.0 0.32 0.77 1 ...
Page 15
Noise Parameter Applications Information F values at 2 GHz and higher are based on min measurements while the F below 2 GHz have been mins extrapolated. The F values are based on a set of min 16 noise figure measurements ...
Page 16
... ATF-35143 SC-70 4 Lead, High Frequency Model Optimized for 0.1 – 6.0 GHz EQUATION La=0.1 nH EQUATION Lb=0.1 nH EQUATION Lc=0.8 nH EQUATION Ld=0.6 nH EQUATION Rb=0.1 OH EQUATION Ca=0.15 pF EQUATION Cb=0. LOSSYL GATE_IN L=Lb L=Lc R=Rb C= LOSSYL SOURCE L=Lb L=La R=Rb This model can be used as a design tool. It has been tested on MDS for various specifications ...
Page 17
... Part Number Ordering Information No. of Part Number Devices ATF-35143-TR1G 3000 ATF-35143-TR2G 10000 ATF-35143-BLKG 100 Package Dimensions SC-70 4L/SOT-343 1.30 (.051) BSC HE 1.15 (.045) BSC DIMENSIONS (mm) SYMBOL MIN. MAX. E 1.15 1.35 D 1.85 2.25 HE 1.80 2.40 A 0.80 1.10 A2 0.80 1.00 A1 0.00 0.10 b 0.25 ...
Page 18
Recommended PCB Pad Layout for Avago’s SC70 4L/SOT-343 Products 1.30 0.051 1.00 0.039 2.00 0.60 0.079 0.024 0.9 0.035 1.15 0.045 mm Dimensions in inches Device Orientation REEL CARRIER TAPE USER FEED DIRECTION COVER TAPE 18 TOP VIEW END VIEW ...
Page 19
Tape Dimensions and Product Orientation For Outline DESCRIPTION CAVITY LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER PERFORATION DIAMETER PITCH POSITION CARRIER TAPE WIDTH THICKNESS COVER TAPE WIDTH TAPE THICKNESS DISTANCE CAVITY TO PERFORATION (WIDTH DIRECTION) ...