9-1393792-9 Tyco Electronics, 9-1393792-9 Datasheet - Page 381

• Manufacturer Part Number: 9-1393792-9
• Description: Electromechanical Relay DPDT 3A 24VDC 2.88KOhm Through Hole
• Manufacturer: Tyco Electronics
• Type: Signal Relayr

Specifications of 9-1393792-9

• Contact Arrangement: DPDT
• Dc Coil Voltage: 24 V
• Coil Current: 8.33 mA
• Mounting: Through Hole

Operating Diagram
Electrical Characteristics (Thermal Derating Curves)
*See Derating Curves
† Random Turn-on Units have a Random Turn-on circuit instead of Zero Voltage Circuit
Outline Dimensions
Dimensions are shown for
reference purposes only.
Output Specifications (@ 25° C, unless otherwise specified)
VDC Input
Control B
VDC Input
Control A
Parameter
Load Voltage Range V
Peak Voltage (Min.)
Load Current Range I *
Thermal Resistance, Junction to Baseplate (R
Turn-On Time (Max.)
Turn-Off Time (Max.)
I t Rating
Load Power Factor Rating
One Second Surge Current (Max.)
Single Cycle Surge Current (Max.)
Leakage Current (Off-State) (Max.)
On-State Voltage Drop (Max.)
Static dv/dt (Off-State) (Min.)
2
50.0
40.0
30.0
20.0
10.0
0.0
25A Units
+
+
–
–
20
25
30
Ambient Temperature (°C)
35
L
L
40
45
VOLTAGE
VOLTAGE
50
CIRCUIT
CIRCUIT
Tolerance: ±.035 (0.88)
ZERO
ZERO
55
60
†
†
65
70
θ
J-B
Dimensions are in inches over
(millimeters) unless otherwise
specified.
75
) (Max.)
80
0.7°C/W
1.0°C/W
1.5°C/W
2.0°C/W
A2
B2
A1
B1
(32.0)
Output A
Output B
1.26
(22.6)
.89
Both Sections On
f = 47 - 63 Hz.
V = 280V rms
Conditions
L
Resistive
t = 1 Min.
t = 8.3 ms
I = Max.
I = Max.
f = 60 Hz.
f = 60 Hz.
L
L
Catalog 1308242
Issued 3-03
Specifications and availability
subject to change.
Heatsink Recommendations
• We recommend that solid state relay modules be mounted to a
• The heatsink mounting surface should be a smooth (30-40 micro-inch
• An even coating of thermal compound (Dow Corning DC340 or
• The module should be mounted to the heatsink using two #10 screws.
heatsink sufficient to maintain the module’s base temperature at less
than 85°C under worst case ambient temperature and load conditions.
finish), flat (30-40 micro-inch flatness across mating area), un-painted
surface which is clean and free of oxidation.
equivalent) should be applied to both the heatsink and module mounting
surfaces and spread to a uniform depth of .002” to eliminate all air
pockets.
80.0
70.0
60.0
50.0
40.0
30.0
20.0
10.0
0.0
40A Units
20
mA rms
A Sec.
A peak
A peak
V peak
V peak
A rms
25
Units
V rms
°C/W
V/µs
2
ms
ms
30
Ambient Temperature (°C)
35
40
Input Terminal Connectors are available from
several different manufacturers.
AMP P/N: 103976-3 or 640440-4
Methode P/N: 1300-004-422
Consult your local distributor for these or
equivalent connectors.
45
50
<0.1 for Random Voltage Turn-On Models
55
8.33 for Zero Voltage Turn-On Models
25A Models
60
0.1-25
1,041
150
500
1.4
0.6
65
70
75
0.5 - 1.0
24-280
8.33
500
80
550
0.1
0.5°C/W
1.0°C/W
1.5°C/W
2.0°C/W
www.tycoelectronics.com
Technical support:
Refer to inside back cover.
40A Models
0.1-40
2,435
234
780
1.3
0.6
P&B
1107