9-1393792-9 Tyco Electronics, 9-1393792-9 Datasheet - Page 383

• Manufacturer Part Number: 9-1393792-9
• Description: Electromechanical Relay DPDT 3A 24VDC 2.88KOhm Through Hole
• Manufacturer: Tyco Electronics
• Type: Signal Relayr

Specifications of 9-1393792-9

• Contact Arrangement: DPDT
• Dc Coil Voltage: 24 V
• Coil Current: 8.33 mA
• Mounting: Through Hole

Operating Diagram
*See Thermal Derating Curves. Note: While each output section is rated for a maximum of 20A, the maximum output per package is 60A.
Electrical Characteristics (Thermal Derating Curves)
OUTPUT B
OUTPUT D
Dimensions are shown for
reference purposes only.
How To Use These Curves
Knowing maximum load current and maximum ambient temperature, use derating curves to determine required heat sink and maximum allowable base plate
temperature. On left hand power dissipation curve, locate the point corresponding to maximum load current. Extend a line to the right from that point to the
intersection of vertical line on right hand chart corresponding to maximum ambient temperature. From heat sink curve, read directly or extrapolate required heat
sink size. Extend the line farther to the right and read on the right hand scale the maximum allowable base plate temperature.
Outline Dimensions
Output Specifications (@ 25° C, unless otherwise specified)
(58.4)
Repetitive Blocking Voltage (Min.)
Load Current Range I *
Thermal Resistance, Junction to Case (R
Turn-On Time (Max.)
Turn-Off Time (Max.)
I t Rating
Load Power Factor Rating
Parameter
Load Voltage Range V
2.3
Single Cycle Surge Current (Min.)
Leakage Current (Off-State) (Max.)
On-State Voltage Drop (Max.)
Static dv/dt (Off-State) (Min.)
2
80
60
40
20
(47.5)
0
1.87
B1
B2
D1
D2
Loads Current (A rms)
15
†
A1
B1
A1
DC SEC. A –
DC SEC. B –
Random Turn-On Units Have A Random Turn-On Circuit Instead Of A Zero Voltage Circuit
B2
A2
30
VOLTAGE
VOLTAGE
CIRCUIT †
CIRCUIT †
ZERO
ZERO
(44.45)
L
L
1.75
45
– DC SEC. C
+ DC COMM
– DC SEC. D
D1
C1
60 0
MTNG HOLE / SLOT 2 PLCS.
D2
C2
Ambient Temp. (°C)
-(D)
EQUIVALENT CIRCUIT ONLY
20
.170 (4.3) DIA.
ON .100 (2.54) CENTERS
Q.C. TERMS
-(B)
θ
.250 (6.35)
8 PLACES
J-C
.025 (.635) SQ. PINS
) (Max.)
40
Dimensions are in inches over
(millimeters) unless otherwise
specified.
60
+
COMMON
(28.57)
1.125
80
-(A)
105
75
90
-(C)
.375
(9.5)
f = 60 Hz. V = 280Vrms
All Sections On
V = 280Vrms
t = 8.3 ms
f = 60 Hz.
f = 60 Hz.
Conditions
Resistive
L
I = Max.
I = Max.
L
L
(21.6)
VOLTAGE
VOLTAGE
CIRCUIT †
CIRCUIT †
.85
Catalog 1308242
ZERO
ZERO
L
Issued 3-03
Specifications and availability
subject to change.
A2
C2
A1
C1
OUTPUT A
OUTPUT C
mA rms
Example #1:
Given: I
Find: Minimum heatsink required
Solution: From Thermal Dissipation Graph
Example #2:
Given: SSRQ24020
Find: Maximum rating mounting to 1.0°C/W HS @ 60°C All
sections ON
Solution: From Thermal Dissipation Graph
A Sec.
V peak
A peak
V peak
Heatsink Recommendations
• We recommend that solid state relay modules be
• The heatsink mounting surface should be a smooth
• An even coating of thermal compound (Dow Corning
• The module should be mounted to the heatsink using
°C/W
A rms
V rms
Units
V/µs
2
ms
ms
mounted to a heatsink sufficient to maintain the
module’s base temperature at less than 85°C under
worst case ambient temperature and load conditions.
(30-40 micro-inch finish), flat (30-40 micro-inch
flatness across mating area), un-painted surface which
is clean and free of oxidation.
DC340 or equivalent) should be applied to both the
heatsink and module mounting surfaces and spread to
a uniform depth of .002” to eliminate all air pockets.
two #10 screws.
Input Terminals mate with the following
connectors or equivalent:
AMP P/N: 103976-4
Consult your local distributor for connectors.
L
= Four 7 .5A loads @ 60°C
4 x 7 .5A = 30A 4 sections ON
Heatsink = 2°C/W minimum
Rating mounted to 1.0°C/W HS @ 60°C = 36A total
9A for 4 Sections ON = 36A total
12A for 3 Sections ON = 36A total
0.1 for Random Voltage Turn-On Models
8.3 for Zero Voltage Turn-On Models
0.5 - 1.0
24-280
.15-20
+
- 600
250
200
260
1.6
1.2
8.3
10
www.tycoelectronics.com
Technical support:
Refer to inside back cover.
P&B
1109