71M6541F-DB Maxim Integrated Products, 71M6541F-DB Datasheet - Page 91
71M6541F-DB
Manufacturer Part Number
71M6541F-DB
Description
Power Management Modules & Development Tools 71M6541 Eval Kit
Manufacturer
Maxim Integrated Products
Datasheet
1.71M6541F-DB.pdf
(165 pages)
Specifications of 71M6541F-DB
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 91 of 165
- Download datasheet (3Mb)
application, the 32-bit CE sequentially processes the samples from the voltage inputs on pins IA, VA,
IB, etc., performing calculations to measure active power (Wh), reactive power (VARh), A
•
•
•
•
These interrupts are connected to the MPU interrupt service inputs as external interrupts. CE_BUSY
indicates that the CE is actively processing data. This signal occurs once every multiplexer cycle (typically
396 µs), and indicates that the CE has updated status information in its CESTATUS register (CE RAM 0x80).
XFER_BUSY indicates that the CE is updating data to the output region of the RAM. This indication
occurs whenever the CE has finished generating a sum by completing an accumulation interval
determined by SUM_SAMPS[12:0], I/O RAM 0x2107[4:0], 2108[7:0], (typically every 1000 ms). Interrupts to
the MPU occur on the falling edges of the XFER_BUSY and CE_BUSY signals.
WPULSE and VPULSE are typically used to signal energy accumulation of real (Wh) and reactive (VARh)
energy. Tying WPULSE and VPULSE into the MPU interrupt system can support pulse counting.
XPULSE and YPULSE can be used to signal events such as sags and zero crossings of the mains voltage
to the MPU. Tying these outputs into the MPU interrupt system relieves the MPU from having to read the
CESTATUS register at every occurrence of the CE_BUSY interrupt in order to detect sag or zero crossing
events.
Refer to
firmware.
3.5
The data flow between the Compute Engine (CE) and the MPU is shown in
for four-quadrant metering. These measurements are then accessed by the MPU, processed further and
output using the peripheral devices available to the MPU.
Both the CE and multiplexer are controlled by the MPU via shared registers in the I/O RAM and in RAM.
The CE outputs a total of six discrete signals to the MPU. These consist of four pulses and two interrupts:
v1.1
CE_BUSY
XFER_BUSY
WPULSE, VPULSE (pulses for active and reactive energy)
XPULSE, YPULSE (auxiliary pulses)
Data Flow and MPU/CE Communication
MUX
5.3 CE Interface Description
Samples
© 2008–2011 Teridian Semiconductor Corporation
CE
I/O RAM (Configuration RAM)
Figure 30: MPU/CE Data Flow
for additional information on setting up the device using the MPU
Pulses
CECONFIG
CESTATUS
XRAM
Control
XFER_BUSY
WPULSE
CE_BUSY
XPULSE
YPULSE
VPULSE
MPU
Figure
Interrupts
30. In a typical
2
h, and V
Processed
Metering
Data
2
h
91
Related parts for 71M6541F-DB
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: