5962-8670901XA E2V, 5962-8670901XA Datasheet - Page 4

• Manufacturer Part Number: 5962-8670901XA
• Manufacturer: E2V

Specifications of 5962-8670901XA

• Lead Free Status / RoHS Status: Supplier Unconfirmed

DSCC FORM 2234
APR 97
shall be as specified on figure 2. When required in groups A, B, or C (see 4.3.1c), the devices shall be programmed by the
manufacturer prior to test in a checkerboard pattern (a minimum of 50 percent of the total number of gates programmed) or to
any altered item drawing pattern which includes at least 25 percent of the total number of gates programmed.
drawing.
as specified in table I and shall apply over the full case operating temperature range.
tests for each subgroup are described in table I.
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For
packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the
option of not marking the "5962-" on the device.
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-
38535, appendix A and the requirements herein.
with each lot of microcircuits delivered to this drawing.
appendix A.
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
in a wide variety of configurations; two processing options are provided for selection in the contract, using an altered item
drawing.
and table II. It is recommended that users perform subgroups 7 and 9 after programming to verify the specific program
configuration.
herein, including the requirements of the altered item drawing, shall be satisfied by the manufacturer prior to delivery.
3.10 Processing options. Since the device is capable of being programmed by either the manufacturer or the user to result
3.10.1 Unprogrammed device delivered to the user. All testing shall be verified through group A testing as defined in 3.2.3.1
3.10.2 Manufacturer-programmed device delivered to the user. All testing requirements and quality assurance provisions
3.2.3 Truth table.
3.2.3.1 Unprogrammed devices. The truth table for unprogrammed devices for contracts involving no altered item drawing
3.2.3.2 Programmed devices. The truth table for programmed devices shall be as specified by an attached altered item
3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
DEFENSE SUPPLY CENTER COLUMBUS
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43216-5000
STANDARD
SIZE
A
used.
REVISION LEVEL
E
SHEET
5962-86709
4