PIC18F65K90T-I/MR Microchip Technology, PIC18F65K90T-I/MR Datasheet - Page 413

• Manufacturer Part Number: PIC18F65K90T-I/MR
• Description: 32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm T/R
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F65K90T-I/MR

• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 32 KB
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 8
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 53
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN Exposed Pad
• Lead Free Status / Rohs Status: Details

The CTMU current source may be trimmed with the
trim bits in CTMUICON using an iterative process to get
the exact current desired. Alternatively, the nominal
value without adjustment may be used. That value may
be stored by software for use in all subsequent
capacitive or time measurements.
To calculate the value for R
must be chosen. Then, the resistance can be
calculated.
For example, if the A/D Converter reference voltage is
3.3V, use 70% of full scale (or 2.31V) as the desired
approximate voltage to be read by the A/D Converter. If
the range of the CTMU current source is selected to be
0.55  A, the resistor value needed is calculated as,
R
if the current source is chosen to be 5.5  A, R
be 420,000 Ω, and 42,000 Ω if the current source is set
to 55  A.
FIGURE 27-2:
 2009-2011 Microchip Technology Inc.
CAL
= 2.31V/0.55 A , for a value of 4.2 M Ω . Similarly,
R
ANx
CAL
CTMU CURRENT SOURCE
CALIBRATION CIRCUIT
Current Source
MUX
PIC18F87K90
CAL
A/D Converter
, the nominal current
A/D
A/D
Trigger
CTMU
CAL
would
PIC18F87K90 FAMILY
A value of 70% of full-scale voltage is chosen to make
sure that the A/D Converter was in a range that is well
above the noise floor. If an exact current is chosen to
incorporate the trimming bits from CTMUICON, the
resistor value of R
ingly. R
resistor values. R
available, in light of the precision needed for the circuit
that the CTMU will be measuring. A recommended
minimum would be 0.1% tolerance.
The following examples show a typical method for
performing a CTMU current calibration.
•
•
Example 27-1
A/D Converter and the CTMU.
This routine is typical for applications using both
modules.
Example 27-2
actual calibration routine.
This method manually triggers the A/D Converter to
demonstrate the entire step-wise process. It is also
possible to automatically trigger the conversion by
setting the CTMU’s CTTRIG bit (CTMUCONH<0>).
CAL
may also be adjusted to allow for available
demonstrates how to initialize the
demonstrates one method for the
CAL
CAL
should be of the highest precision
may need to be adjusted accord-
DS39957D-page 413