ISL12026IBZ-T Intersil, ISL12026IBZ-T Datasheet - Page 11
![IC RTC/CALENDAR EEPROM 8-SOIC](/photos/6/58/65825/isl12026ibz-t_sml.jpg)
ISL12026IBZ-T
Manufacturer Part Number
ISL12026IBZ-T
Description
IC RTC/CALENDAR EEPROM 8-SOIC
Manufacturer
Intersil
Type
Clock/Calendar/EEPROMr
Datasheet
1.ISL12026IBZ-T.pdf
(24 pages)
Specifications of ISL12026IBZ-T
Memory Size
4K (512 x 8)
Time Format
HH:MM:SS (12/24 hr)
Date Format
YY-MM-DD-dd
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Rohs Compliant
YES
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
ISL12026IBZ-TTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL12026IBZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
INT Register: Interrupt Control and
Frequency Output Register
IM, AL1E, AL0E - Interrupt Control and Status Bits
There are two Interrupt Control bits, Alarm 1 Interrupt Enable
(AL1E) and Alarm 0 Interrupt Enable (AL0E) to specifically
enable or disable the alarm interrupt signal output
(IRQ/F
AL1E or AL0E or both bits are set to ‘1’ and both the FO1
and FO0 bits are set to 0 (F
The IM bit enables the pulsed interrupt mode. To enter this
mode, the AL0E or AL1E bits are set to “1”, and the IM bit to
“1”. The IRQ/F
alarm occurs. This means that once the interrupt mode alarm
is set, it will continue to alarm for each occurring match of the
alarm and present time. This mode is convenient for hourly or
daily hardware interrupts in microcontroller applications such
as security cameras or utility meter reading.
In the case that both Alarm 0 and Alarm 1 are enabled, the
IRQ/F
the RTC (both alarms can provide hardware interrupt). If the
IM bit is also set to "1", the IRQ/F
of the alarms as well.
FO1, FO0 - Programmable Frequency Output Bits
These are two output control bits. They select one of three
divisions of the internal oscillator, that is applied to the
IRQ/F
this output. When using this function, the Alarm output
function is disabled.
FO1
0
0
0
0
1
1
1
1
TABLE 4. PROGRAMMABLE FREQUENCY OUTPUT BITS
0
0
1
1
OUT
OUT
OUT
0
0
1
1
0
0
1
1
FO0
pin will be pulsed each time either alarm matches
output pin. Table 4 shows the selection bits for
). The interrupts are enabled when either the
0
1
0
1
0
1
0
1
0
1
0
1
OUT
PROTECTED ADDRESSES
output will now be pulsed each time an
None (Default)
180
100
000
000
000
000
000
Alarm output (F
TABLE 3.
ISL12026
OUTPUT FREQUENCY
OUT
h
h
h
h
h
h
h
11
– 1FF
– 1FF
– 1FF
– 03F
– 07F
– 0FF
– 1FF
disabled).
OUT
32.768kHz
4096Hz
h
h
h
h
h
h
h
1Hz
will be pulsed for each
OUT
disabled)
ARRAY LOCK
First 16 Pages
First 4 Pages
First 8 Pages
Upper 1/4
Upper 1/2
Full Array
Full Array
ISL12026, ISL12026A
None
Oscillator Compensation Registers
There are two trimming options.
• ATR. Analog Trimming Register
• DTR. Digital Trimming Register
These registers are non-volatile. The combination of analog
and digital trimming can give up to -64 to +110 ppm of total
adjustment.
ATR Register - ATR5, ATR4, ATR3, ATR2, ATR1,
ATR0: Analog Trimming Register
6 analog trimming bits, ATR0 to ATR5, are provided in order
to adjust the on-chip load capacitance value for frequency
compensation of the RTC. Each bit has a different weight for
capacitance adjustment. For example, using a Citizen CFS-
206 crystal with different ATR bit combinations provides an
estimated ppm adjustment range from -34 to +80ppm to the
nominal frequency compensation.
The effective on-chip series load capacitance, C
ranges from 4.5pF to 20.25pF with a mid-scale value of
12.5pF (default). C
controlled capacitors, C
and X2 pins to ground (see Figure 8). The value of C
C
The effective series load capacitance is the combination of
C
For example, C
(ATR = 100000) = 4.5pF, and C
The entire range for the series combination of load capacitance
goes from 4.5pF to 20.25pF in 0.25pF steps. Note that these
are typical values.
C
C
C
X2
X1
LOAD
LOAD
X
=
is given by Equation 1:
and C
(
16 b5
=
=
⋅
---------------------------------- -
⎛
⎝
⎛
⎝
16 b5
---------------------------------------------------------------------------------------------------------------------------- -
X2
---------- -
C
1
X1
+
:
⋅
8 b4
X1
X2
LOAD
1
+
⋅
FIGURE 8. DIAGRAM OF ATR
---------- -
C
+
1
8 b4
X2
LOAD
+
⋅
(ATR = 00000) = 12.5pF, C
4 b3
⎞
⎠
C
C
X1
X2
⋅
+
X1
4 b3
is changed via two digitally
+
⋅
and C
2 b2
⋅
+
LOAD
2 b2
2
+
⋅
X2
1 b1
(ATR = 011111) = 20.25pF.
OSCILLATOR
⋅
, connected from the X1
+
CRYSTAL
1 b1
+
⋅
0.5 b0
+
⋅
0.5 b0
LOAD
+
November 30, 2010
⋅
9
LOAD
)pF
+
9
X1
⎞ pF
⎠
,
FN8231.9
(EQ. 1)
(EQ. 2)
and