2-487952-8 TE Connectivity, 2-487952-8 Datasheet - Page 3

• Manufacturer Part Number: 2-487952-8
• Description: 028 1MM FPC BTM HORZ
• Manufacturer: TE Connectivity

Specifications of 2-487952-8

• Termination Method To Pc Board: Surface Mount
• Pcb Mounting Orientation: Right Angle
• Pcb Mount Alignment: Without
• Pcb Mount Retention: With
• Actuator Type: Stuffer
• Shrouded: Yes
• Sealed: No
• Strain Relief: Without
• Contact Current Rating, Max (a): 1
• Operating Voltage Reference: AC
• Operating Voltage (vac): 200
• Shielded: No
• Tail Orientation: In-line
• Profile Height (y-axis) (mm [in]): 2.56 [0.1008]
• Centerline (mm [in]): 1.00 [0.039]
• Number Of Positions: 28
• Selectively Loaded: No
• Pcb Mount Retention Type: Solder Pads
• Length (x-axis) (mm [in]): 35.92 [1.4142]
• Width (z-axis) (mm [in]): 6.54 [0.2575]
• Contact Plating, Mating Area, Material: Tin-Lead
• Contact Plating, Mating Area, Thickness (µm [?in]): 0.381 [15]
• Tail Plating Material: Tin-Lead
• Tail Plating, Thickness (µm [?in]): 0.381 [15]
• Contact Design: Single Beam
• Housing Material: Liquid Crystal Polymer (LCP)
• Contact Mating Location: Bottom
• Flex Cable Thickness (mm [in]): 0.3 [0.012]
• Housing Color: Ivory
• Rohs/elv Compliance: Not ELV/RoHS compliant
• Lead Free Solder Processes: Reflow solder capable to 245°C, Reflow solder capable to 260°C
• Circuit Identification Feature: With
• Operating Temperature (°c [°f]): -40 – +85 [-40 – +185]
• Zif/non-zif: ZIF
• Contact Transmits (typical Application): Signal (Data)
• Pick And Place Cover: Without
• Packaging Method: Tape & Reel

3.6.
Rev C
Contact retention.
Thermal shock.
Humidity-temperature cycling.
Temperature life.
NOTE
Product Qualification and Requalification Test Sequence
NOTE
Test Description
Shall meet visual requirements, show no physical damage and shall meet the requirements of
additional tests as specified in the Test Sequence in Figure 2.
(a) See paragraph 4.1.A.
(b) Numbers indicate sequence in which tests are performed.
Examination of product
Termination resistance
Insulation resistance
Dielectric withstanding voltage
Solderability
Vibration
Physical shock
Durability
Contact retention
Thermal shock
Humidity-temperature cycling
Temperature life
Test or Examination
Contacts shall not dislodge.
See Note.
See Note.
See Note.
ENVIRONMENTAL
Figure 1 (end)
Requirement
Figure 2
1,7
2,6
1
4
5
3
Test Sequence (b)
Test Group (a)
1,7
2,6
2
3
4
5
1,8
2,6
3,7
3
9
4
5
TE Spec 109-30.
Apply axial load off 100 grams to
contacts in vertical direction and
hold for 30 seconds minimum.
TE Spec 109-22.
Subject mated samples to 5 cycles
between -40 and 85° C.
TE Spec 109-23-3, Condition B.
Subject mated samples to 10
cycles between 25 and 65° C at
95% RH. Final measurements shall
be taken during recovery period.
TE Spec 109-43.
Subject mated samples to
temperature life at 85° C for 500
hours.
1,3
4
2
Procedure
108-1393
3 of 6